Regulatory Compliance Notices | Actiontec electronic GT701WG-QW04

Notices

Regulatory Compliance Notices

Class B Equipment

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that inter- ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by implementing one or more of the following measures:

sReorient or relocate the receiving antenna;

sIncrease the separation between the equipment and receiver;

sConnect the equipment to an outlet on a circuit different from that to which the receiver is connected;

sConsult the dealer or an experienced radio or television technician for help.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Actiontec Electronics, Inc., may void the user’s authority to operate the equipment.

Declaration of conformity for products marked with the FCC logo – United States only.

105

Image 110

Actiontec electronic GT701WG-QW04 user manual Regulatory Compliance Notices, Modifications, Class B Equipment

Contents

DSL Modem Table of Contents Specifications Using UtilitiesTroubleshooting Reference Glossary Firewall Security Level Services Limited Warranty 107 105 This page left intentionally blank Minimum System Requirements Package ContentsIntroduction1 Features DSL Light Power LightWireless Light Internet Light Phone Port Reset SwitchLine Port USB Port Other Problems Power PortUsed to connect the Power Cord to the Modem DSL service outage support and repair DSL service installation support Advanced Feature Support Wired/Wireless Upgrade Introduction This page left intentionally blank Disconnecting from the Internet Using Qwest DSLConnecting to the Internet This page left intentionally blank To configure the Modem for basic operation Performing a Basic SetupBasic Setup Page Changing the User Name and Password Click Save and Restart at the bottom of the screen To set up the Modem to use a single static IP address Setting Up Static IP AddressConfiguring for a Single Static IP Address Page Setting Up Static IP Page Click Save and Restart at the bottom of the screen Configuring for a Block of Static IP Addresses To set up the Modem to use a block of static IP addresses Setting Up Static IP Page Dhcp Server Configuration screen, select Static from Click Save and Restart from the menu on the left side Click Save and Restart at the bottom of the screen Configuring5 Advanced Settings Accessing Advanced Settings WAN IP Address Transparent Bridging PPP Auto Connect Encapsulation PPPoA only Save & Apply Specify a Static IP Address Wireless Settings Channel Off WEP WEP+802.1x WPA Wireless MAC Authentication Wireless Advanced Settings Dhcp Server DNS Dynamic or Static Dhcp Server ConfigurationBeginning IP Address, Ending IP Address DNS Server Services Blocking Website Blocking Remote Management/Telnet Port Forwarding To remove forwarded ports, highlight them, then click Remove DMZ Hosting Clicking Advanced brings up the Advanced Port Forward screen Firewall Dynamic Routing NAT Network Address Translation Static Routing IP QoS Setting Source Telnet Timeout Setting LAN IP Address This page left intentionally blank Viewing Modem’s Status Accessing StatusTo access the Status screens, follow these instructions Current Status Viewing the Modem’s Status WAN Status LAN Status Dhcp User ListPage Using Utilities Web Activity Log DSL Settings Restore Default Settings Upgrade Firmware This page left intentionally blank Cannot Connect to the Internet TroubleshootingLAN Connection Failure CMD Time out error occurs when entering a URL or IP Address This page left intentionally blank Reference Locating Computer Information Locating Windows Operating System Files Appendix a Reference Click Search Static IP Address On the Computer Windows 98 SEPage 192.168.0.2 Windows Me Enter the following numbers in the Subnet mask text box Appendix b Static IP on the Computer Do not include the periods they are automatically entered Windows Page Appendix b Static IP on the Computer Enter the following numbers in the IP Address text box Windows XP Page Appendix b Static IP on the Computer Enter the following address in the IP Address text box Comparing DSL Service with a Dial-Up Modem Computer Security Internet Browsers Modem SecurityComputer Security Electronic Security This page left intentionally blank WAN PPP, DHCP, Static IP Specifications dGeneral Full-rate Adsl Interface Power, DSL, Internet, Ethernet, USB, Wireless Wireless Operating RangeLED Indicators Environmental Access Point GlossaryPage Ssid This page left intentionally blank Firewall Security Level Services Medium Security Level Low Security Level Service Acronym Definitions 323 Real audio/videoIcmp 120 Alternativeg System Setup ClassicPage Appendix g Alternative System Setup Connecting to the ISP Then press Enter on the keyboard Appendix g Alternative System Setup 100 Self Help Basic Setup Support Getting OnlineAdditional Technical Support Options Qwest Advanced Feature Support Networking LAN Support Appendix h Additional Technical Support Options 104 Class B Equipment Regulatory Compliance NoticesModifications Miscellaneous Legal Notices All other names are the property of their respective owners Limited Warranty 107 108 Limited Warranty 110