Manuals / Actiontec electronic / Computer Equipment / Network Router

Actiontec electronic GT704WR user manual Cable/DSL Port, Reset Switch, Power Port

Models: GT704WR

1 115

Download 115 pages 46.11 Kb

Page 8

Cable/DSL Port

Chapter 1 Introduction

Cable/DSL Port

The Cable/DSL port is used to connect the Router to an Ethernet cable/ DSL modem.

Reset Switch

Depressing the Reset switch for one or two seconds will power cycle the Router (similar to unplugging and then plugging in the Router’s Power cord). To restore the Router’s factory default settings, depress and hold the Reset switch for approximately 15 seconds. The reset process will start about 10 seconds after releasing the switch.

Power Port

The Power port is used to connect the Power cord to the Router.

NWarning: Do not unplug the Power cord from the Router dur- ing the reset process. Doing so may result in permanent damage to the Router.

5

Image 8

Actiontec electronic GT704WR user manual Cable/DSL Port, Reset Switch, Power Port

Contents

Wireless Cable/DSL Router Solutions for the Digital LifeUser Manual 54 MbpsTable of Contents 2 Setting Up the Router3 Performing a Basic Setup Using Advanced Setup7 Setting Up a Network Package Contents Introduction1Features Minimum System RequirementsPower Light Getting to Know the RouterWireless Light Internet LightEthernet Lights Ethernet PortsReset Switch Power PortCable/DSL Port The Power port is used to connect the Power cord to the RouterActiontec 54 Mbps Wireless Cable/DSL Router User Manual This page left intentionally blankthe Router Setting UpConnecting a Computer to the Router 2. Read the instructions, select Initial Setup by clicking on the appropriate check box, then click Next Chapter 2 Setting Up the Router 6. Locate the Ethernet cable connecting the cable/DSL modem to the computer, then click Next 9. Get the yellow Ethernet cable from the kit, then click Next Chapter 2 Setting Up the Router8. Get the Router from the kit, then click Next 10. Plug one end of the yellow Ethernet cable into one of the yellow Ethernet ports on the back of the Router, then click Next 12. Get the black Power cord from the kit. Click Next Chapter 2 Setting Up the Router14. Plug the larger end of the black Power cord into a power outlet. Click Next Chapter 2 Setting Up the Router 18. Unplug the power cord of the cable/DSL modem, count to 10, then plug the power cord back in again. This resets the cable/DSL modem, allowing it to communicate with the Router. Cick Next If Dynamic IP DHCP is selected, got directly to step Chapter 2 Setting Up the RouterIf Static IP is selected, go directly to step 22. If Static IP was selected in step 21, enter the IP Address, Subnet, Router, DNS 1, and DNS 2 information if applicable in the proper text boxes. This information should be available in the ISP. When finished, click Next and go directly to step 24. The Installation Buddy checks the configuration of the Router Actiontec 54 Mbps Wireless Cable/DSL Router User Manual This page left intentionally blankPerforming a Basic SetupBasic Setup If DSL Option 1 was chosen, go directly to step 8. Click Save and Restart in the “Save and Restart” screen Changing the Admin User Name and Password Chapter 3 Performing a Basic Setup 4. The “Save and Restart” page appears. Click “Save and Restart” to save the set- tings changed in the Change Admin Username/Password screenActiontec 54 Mbps Wireless Cable/DSL Router User Manual This page left intentionally blankAccessing Advanced Setup Using AdvancedSetup 4. In the next screen, read the recommendations. To perform an advanced setup on the Router, click Begin Advanced Setup Obtain an IP Address through PPPoE WAN IP AddressChapter 4 Using Advanced Setup Dialout on-demand/Idle timeout Obtain an IP Through DHCPSpecify a Static IP Address Wireless Settings WirelessActiontec 54 Mbps Wireless Cable/DSL Router User Manual ESSIDChapter 4 Using Advanced Setup SecurityWEP+802.1x Actiontec 54 Mbps Wireless Cable/DSL Router User ManualWireless MAC Authentication Wireless Advanced Settings LAN IP Address DHCP ServerDHCP Server Configuration Beginning IP AddressEnding IP Address Services Blocking DNS Dynamic or StaticDNS Server DNS ServerNetmeeting Website BlockingActiontec 54 Mbps Wireless Cable/DSL Router User Manual Remote Management Chapter 4 Using Advanced SetupPort Forwarding Actiontec 54 Mbps Wireless Cable/DSL Router User ManualTo remove forwarded ports, highlight them, then click Remove Clicking Advanced brings up the “Advanced Port Forwarding” screenDMZ Hosting Firewall Dynamic RoutingStatic Routing UPnP Universal Plug and PlayMAC Address Cloning Actiontec 54 Mbps Wireless Cable/DSL Router User ManualStatus Router’s SettingsViewing the WAN - Connection Chapter 5 Viewing the Router’s Settings Routing TableWAN Status Actiontec 54 Mbps Wireless DSL Router User Manual LAN StatusActive User List Using Utilities Web Activity LogRestore Default Settings Upgrade Firmware Chapter 6 Using UtilitiesActiontec 54 Mbps Wireless Cable/DSL Router User Manual This page left intentionally blankSetting Up a Network Ethernet3. Select Wired USB or Ethernet, then click Next Actiontec 54 Mbps Wireless Cable/DSL Router User ManualChapter 7 Setting Up a Network 6. Plug the other end of the yellow Ethernet cable into an Ethernet port on the back of the computer, then click Next 8. In the next window, the Installation Buddy checks the configuration of the Router Wireless Actiontec 54 Mbps Wireless Cable/DSL Router User Manual4. Read the on-screen instructions, then click Finish 3. Select Wireless, then click NextChapter 7 Setting Up a Network Actiontec 54 Mbps Wireless Cable/DSL Router User Manual This page left intentionally blankTroubleshooting TroubleshootingUsing on Network With Another Router/Gateway Physical ConnectionsFrequently Asked Questions Is the Router flash-upgradeable? How do I do it?Which protocols does the Router support? Which connection speeds does the Router support?Can I use an 802.11b wireless card to connect to the Router? Which wireless cards will work with the Router?Do I need a specific cable or DSL modem to use the Router? Will cordless phones interfere with the Router?Can my wireless signal pass through floors, walls, and glass? What is the valid IP range I can use for my home network?How do I find out which IP address my computer is using? NetworkCan I play games between computers on my network, or on the Internet? Yes, if the application is designed to run over a networkWhat is WEP? What is the default username for the Router?What is the difference between 40-bit and 64-bit encryption? How many computers can be connected through the Router?What is WPA? What is NAT and how does it protect my network?How do I make a HEX-based WEP key? Does the Router function as a firewall?Actiontec 54 Mbps Wireless Cable/DSL Router User Manual This page left intentionally blankReference Locating Computer InformationLocating Windows Operating System Files Appendix A Reference Page Windows 98 SE Setting Up Static IPon the Computer 3. Another menu appears. Select Control Panel 4. When the “Control Panel” window appears, double-click NetworkActiontec 54 Mbps Wireless Cable/DSL Router User Manual 6. The “TCP/IP Properties” window appears. Select IP Address Windows Me 3. Another menu appears. Select Control Panel 4. When the “Control Panel” window appears, double-click NetworkAppendix B Setting Up Static IP on the Computer 6. The “TCP/IP Properties” window appears. Click IP Address Windows Actiontec 54 Mbps Wireless Cable/DSL Router User Manual 3. Another menu appears. Select Control PanelAppendix B Setting Up Static IP on the Computer 9. The “Internet Protocol TCP/IP Properties” window appears Windows XP Actiontec 54 Mbps Wireless Cable/DSL Router User Manual 7. The “Internet Protocol TCP/IP Properties” window appears 9. Enter the following address in the “IP Address” text box Comparing Broadband Service with a Dial-Up Modem Computer SecurityRouter Security Computer SecurityElectronic Security Actiontec 54 Mbps Wireless Cable/DSL Router User Manual This page left intentionally blankSpecifications D GeneralEnvironmental Wireless Operating RangeLED Indicators Glossary Ethernet Network PPPoE Point-To-Point Protocol over Ethernet Actiontec 54 Mbps Wireless Cable/DSL Router User Manual This page left intentionally blankHigh Security Level Level Services TableFirewall Security Medium Security Level Low Security LevelService Acronym Definitions Basic Security Levelhttp telnetreal audio/video icmpH.323 T.120Non-Windows G System Setup Classic3. When the “User Mode” window appears, select Advanced, then click OK 1. From the Apple Menu, select System Preferences 2. When the “System Preferences” window appears, click NetworkAppendix G Non-Windows Setup Actiontec 54 Mbps Wireless Cable/DSL Router User Manual Modifications NoticesRegulatory Compliance Notices Miscellaneous Legal Notices Limited Warranty Actiontec 54 Mbps Wireless Cable/DSL Router User Manual Return the product to In the United StatesLimited Warranty Actiontec 54 Mbps Wireless Cable/DSL Router User Manual