ADC H2TU-C-319 List 4E V

LTPH-UM-1049-02, Issue 2 Installation

H2TU-C-319 List 4E January 9, 2002 9

VERIFICATION

Once the H2TU-C is installed, verify that it is operating properly. To do this, monitor the following:

•Status LED

•Status messages reported by the front-panel display (Table2 on page 5 lists the status messages).

Verification without an H2TU-R Remote Unit

If there is no H2TU-R remote unit installed:

1Verify that the H2TU-C powers up. The front-panel display illuminates and reports status messages. (See

Table 2 on page5 lists the messages.)

2Verify that the H2TU-C attempts to communicate with a remote unit (status LED flashes red). Even if a

remote unit is not present, the following events should occur:

aThe front-panel display reports various four-character status messages.

bThe H2TU-C again attempts communication with a remote unit until a remote unit is detected.

Verification with an H2TU-R Remote Unit

If an H2TU-R remote unit has been installed:

1Verify that the H2TU-C powers up. (The front-panel display illuminates and reports various status messages.)

2Verify that the H2TU-C attempts to communicate with the remote unit (status LED flashes red). One of the

following occurs:

•If the remote unit is successfully identified and the HDSL2 loop synchronizes, the H2TU-C status LED

lights a steady green. The H2TU-C reports normal margin messages on the front-panel display.

•If the remote unit is not identified, the H2TU-C reports four-character status messages. The H2TU-C

attempts communication again and reports four-character status messages. The H2TU-C repeats this

cycle until a remote unit is detected.

3Verify that a valid DS1 signal has been applied to the H2TU-C and the H2TU-R.

•If no DS1 signal is being applied to either the H2TU-C or the H2TU-R inputs, then the appropriate DS1

alarms (LLOS or RLOS) display on the front panel and the status LED flashes red.

•If a valid DS1 signal is being supplied to the H2TU-C and H2TU-R, then DS1 alarm indications should

be absent and the status LED should be a steady green.

Contents

Main HiGain HDSL2 U SER M L B K M O D E Revision History of This Manual USING THIS MANUAL I NSPECTING S Page TABLE OF CONTENTS Page LIST OF FIGURES LIST OF TABLES O F C A LTPH-UM-1049-02, Issue 2 Front Panel H2TU-C-319 List 4E January 9, 2002 3 FRONT PANEL DCE Status LED DSX-1 access jacks Craft port Table 1. Front-Panel Description Page Page Table 2. Front-Panel Display Messages (Continued) I V Verification without an H2TU-R Remote Unit Verification with an H2TU-R Remote Unit P USING THE MODE AND LBK PUSHBUTTONS Setting Options through MODE and LBK Resetting to Factory Default Values Displaying System Parameter Settings Disabling an Alarm Loopback Modes USING A MAINTENANCE TERMINAL Connecting to a Maintenance Terminal The Logon Screen Figure 3. Logon Screen Table 4. Logon Screen Menus PROVISIONING TASKS Setting Date and Time Setting Circuit ID Numbers Configuring the System Making Changes to Standard and ADC Options LTPH-UM-1049-02, Issue 2 Provisioning H2TU-C-319 List 4E January 9, 2002 17 Figure 7. Config Menu - Standard Options (defaults shown) Figure 8. Config Menu - ADC Options (defaul ts shown) Page Table 6. H2TU-C-319 List 4E ADC Config Menu Options Table 5. H2TU-C-319 List 4E Standard Config Menu Options (Continued) Page Table 6. H2TU-C-319 List 4E ADC Config Menu Options (Contin ued) Page Page Page Table 9. Extended SuperFrame Format Table 10. SuperFrame Format Page Page Provisioning LTPH-UM-1049-02, Issue 2 28 January 9, 2002 H2TU-C-319 List 4E Test Access Figure 9. Metallic Test Access Block Diagram LTPH-UM-1049-02, Issue 2 Provisioning H2TU-C-319 List 4E January 9, 2002 29 MUX Figure 10. MTA Relays DACS Provisioning LTPH-UM-1049-02, Issue 2 30 January 9, 2002 H2TU-C-319 List 4E Figure 12. H2TU-C-319 List 4E Block Diagram Dual DSX-1 Port Option Resetting to Factory Defaults Clearing the History, Alarm, and Event Log Screens MONITORING SYSTEM ACTIVITY AND P USING THE MONITOR SCREEN TO VIEW SYSTEM ACTIVITY Table 14. Monitor Screen Descriptions USING THE PERFORMANCE SCREENS TO VIEW PERFORMANCE DATA 38 January 9, 2002 H2TU-C-319 List 4E Performance History at the DS1 Interface Figure 16. H2TU-R DS1 31-Day Performance History Figure 17. H2TU-R DS1 25-Hour Performance History Page 40 January 9, 2002 H2TU-C-319 List 4E Performance History at the HDSL2 Interface Figure 19. H2TU-C HDSL2 31-Day Performance History Figure 20. H2TU-C HDSL2 48-Hour Performance History Page 42 January 9, 2002 H2TU-C-319 List 4E Current Statistics Screens for the DS1 Interface Figure 22. H2TU-R DS1 Current Statistics Figure 23. H2TU-C DS1 Current Statistics LTPH-UM-1049-02, Issue 2 Monitoring System Activity and Performance H2TU-C-319 List 4E January 9, 2002 43 Current Statistics for HDSL2 Interface Figure 24. H2TU-C HDSL2 Current Statistics USING THE PERFORMANCE SCREENS TO VIEW ALARM DATA Figure 26. H2TU-R DS1 Alarm History Screen Table 17. DS1 Alarm Descriptions 46 January 9, 2002 H2TU-C-319 List 4E Alarm History at the HDSL2 Interface Figure27 shows the H2TU-C HDSL2 alarm history and Table 18 describes the alarms. Figure 27. H2TU-C HDSL2 Alarm History Screen Table 17. DS1 Alarm Descriptions (Continued) Screen Alarm Front-Panel Alarm Description Table 18. HDSL2 Alarm Descriptions USING THE SYSTEM EVENT LOG TO TRACK EVENTS Table 19. Event Log Entry Messages List USING THE REPORT MENU Table 20. Report Types T SYSTEM ALARMS Alarm Option for the Digital Loop Carrier Feed Retiring System Alarms Remote LOS and AIS Response Figure 30. H2TU-R LOS and AIS Response Priorities OCT55 TEST PATTERN WITH AMI LINE CODE LOOPBACK OPERATION Generic Loopback Commands Special Loopback Commands SmartJack Loopback Commands M ANUAL L OOPBACK S Setting the Loopback Time-Out Option Activating Manual Loopback Mode ACTIVATING MANUAL METALLIC TEST ACCESS IN-BAND LOOPBACK SESSIONS General Troubleshooting Tips GNLB Test Procedures Testing LTPH-UM-1049-02, Issue 2 60 January 9, 2002 H2TU-C-319 List 4E Figure 32. Loopback Modes DSX-1 GNLB loopback codes. LoopbacksToward Customer CI-Customer Interface A2LB Test Procedures Page Page A3LB and A4LB Test Procedures SmartJack Test Procedure APPENDIX A - SPECIFICATIONS P OWER C M AXIMUM P OWER D M AXIMUM C URRENT D LOOP ATTENUATION, INSERTION LOSS, AND REACH Appendix A - Specifications LTPH-UM-1049-02, Issue 2 68 January 9, 2002 H2TU-C-319 List 4E H2TU-C-319 LIST 4E CARD-EDGE CONNECTOR Figure 33. H2TU-C-319 List 4E Card-Edge Connector Network Management Control Bus Fuse Alarm System Alarm Output Pin CRAFT PORT Terminal Figure 35. RS-232 Craft Port Pinouts H2TU-C-319 Terminal APPENDIX B - FUNCTIONAL OPERATION Figure 36. H2TU-C-319 List 4E Block Diagram Page APPENDIX C - COMPATIBILITY APPENDIX D - PRODUCT SUPPORT TECHNICAL SUPPORT R APPENDIX E - ABBREVIATIONS Page Page CERTIFICATION AND WARRANTY FCC CLASS A COMPLIANCE L IMITED W M S AFETY S TANDARDS C ,-Q6o