Manuals
/
Brands
/
Household Appliance
/
Carbon Monoxide Alarm
/
Advantech
/
Household Appliance
/
Carbon Monoxide Alarm
Advantech
PCI-1718 Series
Table 3.7: Summary of Jumper Settings
1
34
94
94
Download
94 pages, 1.52 Mb
PCI-1718 Series User Manual
26
Table 3.7: Summary of Jumper Settings
Jumper
Function Description
JP1 (first)
S0
D0 (default)
JP1 (sec-
ond)
S1
D1 (default)
JP1 (third)
S2
D2 (default)
JP1
(fourth)
S3
D3 (default)
Contents
Main
Page
Page
Page
Contents
Chapter 1 Introduction..................................................... 2
Chapter 2 Installation..................................................... 12
Chapter 3 Signal Connections........................................ 20
Chapter 4 Programming Guide ..................................... 38
Appendix A Specifications ................................................. 52
Appendix D Calibration..................................................... 82
Page
Introduction
Chapter 1 Introduction
1.1 Features
1.2 Applications
1.3 Installation Guide
Page
1.4 Software Overview
1.5 Device Driver Programming Roadmap
Page
1.6 Accessories
Installation
Chapter 2 Installation
2.1 Unpacking
2.2 Driver Installation
Page
2.3 Hardware Installation
2.4 Device Setup & Configuration
Page
Page
Signal Connections
Chapter 3 Signal Connections
3.1 Overview
3.2 Switch and Jumper Settings
3.2.1 Setting the BoardID Switch (SW1)
3.2.2 Channel Configuration, S/E or DIFF (SW2)
3.2.3 D/A Reference Voltage, int./ext. (JP11)
3.2.4 Internal Voltage Reference, -10 V or -5 V (JP10)
3.2.5 Timer Clock Selection (JP8)
3.2.6 Ext. trigger and Counter Gate 0 Control (JP5)
3.2.7 Digital Output, 20-pin or 37-pin Connector (JP1)
Table 3.7: Summary of Jumper Settings
3.2.8 Setting the Time to Reset Digital Outputs
3.3 Signal Connections
3.3.1 I/O Connector Signal Description
Table 3.9: I/O Connector Signal Descriptions
3.3.2 Analog Input Connections
Page
Page
Page
3.3.3 Digital Signal Connections
3.4 Field Wiring Considerations
Page
Programming Guide
Chapter 4 Programming Guide
4.1 Overview
4.2 Programming with the Driver
4.3 Register Programming.
4.3.1 Software Trigger and Polling
Page
41 Chapter 4
4.3.2 Pacer Trigger Mode with Interrupt
Page
Page
Page
45 Chapter 4
4.3.3 Pacer Trigger Mode with Interrupt and FIFO
Page
Page
Page
4.4 Programming with LabVIEW and ActiveDAQ
Page
Page
Appendix A Specifications
A.1 Analog Input
A.2 Analog Output
A.3 Digital Input
A.4 Digital Output
A.5 Counter/Timer
A.6 General
Page
Page
Page
Page
Appendix C Register Structure & Format
C.1 Overview
C.2 I/O Port Address Map
Table C.1: PCI-1718HDU/HGU Register Format (Part 1)
Table C.2: PCI-1718HDU/HGU Register Format (Part 2)
Table C.3: PCI-1718HDU/HGU Register Format (Part 3)
C.3 A/D Data and Channels BASE+00H~01H
C.4 Software A/D Trigger BASE+00H
C.5 A/D Range Control BASE+01H
Note: G3 and G2 are not used for PCL-818L
C.6 MUX Scan Channel Control BASE+02H
C.7 MUX Scan Channel Status BASE+02H
C.8 Digital I/O Registers - BASE + 03/0BH
C.9 D/A Output BASE+04/05H
C.10 FIFO Interrupt Control BASE+06H
C.11 Clear Interrupt Request BASE+08H
C.12 A/D Status BASE+08H
Page
C.13 A/D Control BASE+09H
C.14 Timer/Counter Enable BASE+0AH
C.15 Programmable Timer/Counter BASE+0C~0FH
C.16 Clear FIFO Interrupt Request BASE+14H
C.17 A/D Data and Channel from FIFO - BASE + 17/18H
C.18 FIFO Status BASE+19H
C.19 FIFO Clear BASE+19H
77 Appendix C
C.20 Register Programming Flow Chart
C.20.1 Software Trigger Mode with Polling
PCI-1718 Series User Manual 78
C.20.2 Pacer Trigger Mode with Interrupt
79 Appendix C
C.20.3 Pacer Trigger Mode with Interrupt [FIFO Used]
Page
Page
Appendix D Calibration
D.1 VR Assignment
D.2 A/D Calibration
D.3 D/A Calibration
