EEPROM PARAMETERS
8
The OEM Host can program various parameters that are stored in EEPROM and become active after a
Ta b l e 9 : E E P R O M P a r a m e t e r s
Parameter | EEPROM | Length | Range | Default | Description | |
Address | (Bytes) | |||||
|
|
|
| |||
Product ID | 0x00 | 40 |
|
| Product identifier string. Includes revision infor- | |
|
|
|
|
| mation for software and hardware. | |
|
|
|
|
|
| |
Channel Mask | 0x30 | 4 |
| 0x07FFF800 | When Channel Select is enabled in EEPROM, | |
|
|
|
|
| tells the radio the available channels to use in | |
|
|
|
|
| Channel Select mode. | |
|
|
|
|
|
| |
End Device Poll Rate | 0x34 | 2 | 0x0000 - 0xFFFF | 0x03E8 | Specifies how often the End Device will wakeup | |
|
|
|
|
| from Sleep Mode. and request data from its | |
|
|
|
|
| parent. 1 ms per increment. | |
|
|
|
|
| Note: Valid only for End Devices | |
|
|
|
|
|
| |
Parent Hold Message | 0x39 | 1 | 0x00 - 0xFF | 0x42 | Specifies the amount of time that a Parent | |
|
|
|
|
| Device will hold a message for a sleeping End | |
|
|
|
|
| Device before discarding. 1000 ms per incre- | |
|
|
|
|
| ment. | |
|
|
|
|
| Note: Valid only for Coordinator and Routers | |
|
|
|
|
|
| |
End Device Wake Time | 0x3A | 2 | 0x0000 - 0xFFFF | 0x0064 | Specifies the amount of time that an End | |
|
|
|
|
| Device will remain awake. 1 ms per increment. | |
|
|
|
|
| Note: Valid only for End Devices | |
|
|
|
|
|
| |
End Device Wake Poll | 0x3C | 2 | 0x0000 - 0xFFFF | 0x0032 | Specifies how often the End Device should | |
Rate |
|
|
|
| request messages from its Parent Device while | |
|
|
|
|
| awake. 1 ms per increment. | |
|
|
|
|
| Note: Valid only for End Devices | |
|
|
|
|
|
| |
Stop Bit Delay | 0x3F | 1 | 0x00 - 0xFF | 0x00 | For systems employing the | |
|
|
|
|
| Parity, the serial stop bit might come too early. | |
|
|
|
|
| Stop bit delay controls the width of the last bit | |
|
|
|
|
| before the stop bit occurs. Should be set to 2 | |
|
|
|
|
| times the byte time when used. | |
|
|
|
|
| 0x00 = Disable stop bit delay | |
|
|
|
|
| Note: Stop bit delay only needs to be used | |
|
|
|
|
| when using external RS485 hardware or RS485 | |
|
|
|
|
| DE/RE. | |
|
|
|
|
|
| |
Channel Number | 0x40 | 1 | 0x0B - | 0x0B | RF Channel Number. Used when Channel | |
|
|
| 0x1A |
| Select mode is disabled. | |
|
|
|
|
|
|
www.aerocomm.com