Agilent Technologies Agilent 6031A 1. Performance Specifications, Agilent Technologies Model

Table 1-1. Performance Specifications
Agilent Technologies Model		6033A
DC Output: Voltage, current and power spans indicate range	Volts	0-20 V
over output may be varied using front panel controls.	Amps	0-30 A
	Maximum Power	200-240 W
Load Effect (Load Regulation) Voltage load effect is given for a load	Voltage	0.01%	+ 2 mV
current change equal to the current rating of the supply. Current load
effect is given for a load voltage change equal to the voltage rating of the	Current	0.01%	+ 9 mA
supply.

6038A

0-60 V

0-10 A

200-240 W

0.01% + 3 mV

0.01% + 5 mA

Source Effect (Line Regulation): Given for a change within the rated line voltage for any output within the rated output voltage, current and power of the supply

PARD (Ripple and Noise): Measured at any line voltage and under any load condition within rating (rms 10 Hz to 10 Mhz/p-p 10 Hz to

20 MHz)

Load Effect Transient Recovery: Maximum time required for output voltage to recover with the specified band around the nominal output voltage following a 10% step change in output current while operating in the constant voltage mode

Programming: (25 ± 5°C) Given for control of the output over the GP-IB or with front panel controls

Remote Voltmeter: (25 ± 5°C) Refers to data read back to the controller over the GP-IB

Remote Ammeter: (25 ± 5°C) Refers to data read back to the controller over the GP-IB.

Front Panel Voltmeter: (25 ± 5°C)

Front Panel Ammeter: (25 ± 5°C)

Voltage	0.01%	+ 1 mV
Current	0.01%	+ 6 mA
Voltage	3 mV/30 mV
Current	30 mA/1
Time	1 ms
Level	50 mV
Voltage Accuracy	0.035% + 9 mV
Current Accuracy	0.15%	+20 mA
Accuracy	0.07%	+ 6 mV
Accuracy	0.3% + 25 mA
Range	2 V, 20 V, 200 V
Accuracy	0.07% +6 mV, 11
	mV, 56 mV
Range	20 A, 200 A
Accuracy	0.3% + (20 mA, 65
	mA)

0.01% + 2 mV

0.01% + 2 mA

3 mV/30 mV

5mA/1

1ms

75 mV

0.035% + 40 mV

0.085% + 10 mA

0.07% + 50 mV

0.2% + 11 mA

2 V, 20 V, 200 V

0.07% + 50 mV, 55 mV, 100 mV)

20 A

0.2% + 11 mA

Table 1-2. Supplemental Characteristics
Agilent Technologies Model			6033A
Programming: (25 ± 5°C) Given for control of the		Voltage Resolution	5 mV
output over the GP-IB or with front panel controls		Current Resolution	7.5 mA
Remote Voltmeter: (25 ± 5°C) Refers to data read back to the controller		Resolution	5 mV
over the GP-IB
Remote Ammeter: (25 ± 5°C) Refers to data read back to the controller		Resolution	7.5 mA
over the GP-IB.
Front Panel Voltmeter: (25 ± 5°C)		Resolution	5 mV, 10 mV, 100
			mV
Front Panel Ammeter: (25 ± 5°C)		Resolution	10 mA, 100 mA
Maximum AC Input Current: +6% -13%(48-63) Hz		100 Vac (Opt.100)	6.0 A
		120 Vac (Std.)	6.5 A
		220 Vac (Opt.220)	3.8 A
		240 Vac (Opt.240)	3.6 A
Temperature Coefficient: Output change per degree Celsius change		Voltage	50 ppm + 0.6 mV
in ambient following 30 minute warm-up.		Current	100 ppm + 2 mA
Drift (Stability): Change in output (dc to 20 Hz) over 8-hour internal		Voltage	0.02 % + 1 mV
under constant line, load, and ambient following 30-minute warm-up		Current	0.03% + 10 mA
Programming Response Time: The maximum time required		Settling Band	5 mV
to change from zero volts to full scale voltage or from full	Up	Full Load	100 ms
scale voltage to 2 volts ( 5 volts for Agilent 6035A) and settle		No Load	100 ms
within the specified band. Full load is defined as the	Down	Full Load	200 ms
resistance equal to Vp1/Ip1. Light load is as specified		Light Load	500 ms (50 Ω)
Overvoltage Protection: Trip voltage adjustable via front		Range	0-23 V
panel control using the Display OVP function		Resolution	100 mV
		Accuracy	0.3% + 200 mV
Typical input power at rated output power: (see point P2 on Figure 1-1)			340 W

6038A

15mV

2.5mA

15mV

2.5 mA

15 mV, 15 mV, 100 mV

10mA

6.0A

6.5A

3.8A

3.6A

50ppm + 3 mV

90ppm + 0.3 mA 0.02% + 2 mV 0.03% + 3 mA

15mV

150ms

120ms

150ms

750ms (400 Ω) 0-63 V

100mV

0.25% + 300 mV

325W

16General Information