Agilent Technologies Serials 3004A-05881 to 05885 3023A-06181 and above Agilent 6033A manual

1494-0060	Rack slide kit, non tilting
5060-2865	Service kit, includes extenders for control and power mesh boards, three cables to
	allow GP-IB and PSI boards to lie on table outside unit, and control board test
	connector.
5060-2866	FET service kit. Includes FETs and all components that should be replaced with FETs.
59510A	Relay Accessory
59511A	Relay Accessory (Polarity Reversing)
5062-3960	Rack mounting adapter kit for side mounting one 7-inch high cabinet, includes one
	rack flange and one half-module width extension adapter. (Will be shipped with
	instrument if ordered as Option 908). This rack mounting adapter kit is not compatible
	with front handle kit Agilent P/N 5061-3990).
5062-3961	Rack mounting adapter kit for center mounting one 7-inch high cabinet, includes one
	rack flange and one quarter-module width extension adapter (two kits required), there
	will be surplus of hardware.
5062-3978	Rack flange kit for 7-inch high cabinet. Must be used with another half-module width
	unit of equal depth with lock link kit 5061-9694. (Will be shipped if instrument is
	ordered as Option 800).
5061-9694	Lock link kit for joining units of equal depth, contains hardware for three side-by-side
	joints (four units) and two over-under joints (three units). Locking cabinets together
	horizontally in a configuration wider than one full module is not recommended. 5062-
	3978 and 5061-9694 will be shipped if Option 800 is ordered.
5062-3990	Front handle kit for 7-inch high cabinets. Corresponding flange kit is 5061-2072. This
	front handle kit is not compatible with rack mounting adapter kit (Agilent PIN 5062-
	3960) or Option 908.
5061-2072	Flange kit to be used with front handle kit 5062-3990.
5062-3984	Rack mounting flange kit with handles for 7-inch high cabinet. Must be used with
	another half-module width unit of equal depth with lock link kit 5061-9694.
5062-4003	Bail handle kit for carrying 7-inch high, half-module width cabinet.
1460-1345	Tilt stand (1) snaps into standard foot on instrument, must be used in pairs.
5062-3998	Support shelf bit for mounting on or more 7-inch high cabinets of any depth to 20
	inches.
5062-4027	Front filler panel, half-module width, for 7-inch high cabinet on support shelf.
1494-0065	Slide kit for 5061-0098 support shelf.
06033-60005	Service kit, includes extenders for control and power mesh boards, three cables to
	allow GP-IB and PSI boards to lie on table outside unit, and control board test
	connector.
5060-0138	GP-IB connector non-metric to metric conversion kit.
5060-2860	FET service kit, includes FETs and all components that should be replaced with FETs.
59510A	Relay Accessory
59511A	Relay Accessory (Polarity Reversing)

Instrument and Manual Identification

Agilent Technologies power supplies are identified by a unique two-part serial number, such as 3023A-06181. The first part is the prefix, which denotes the date of the last significant design change and the country of manufacture. Adding 1960 to the first two digits gives the year of the change (30 = 1990, 31 = 1991, etc.) and the second two digits identify the week of that year. The letter indicates the country of manufacture (A = U.S.A.). The second part of the serial number consists of a 5- digit number sequentially assigned to each power supply.

General Information 13