Aiwa XR-M75 To clean the headsand tape paths, GENERAL There is no sound, To clean the cabinet

Occasional care and maintenance of the unit and the software are needed to optimize the performance of your unit.

To clean the cabinet

Use a soft and dry cloth.

If the surfaces are extremely dirty, use a soft cloth lightly moistened with mild detergent solution. Do not use strong solvents, such as alcohol, ”benzine or thinner as these could damage the finish of the unit.

To clean the headsand tape paths

After every 10 hours of use, clean the heads and tape paths with a head cleaning cassette or cotton swab moistened with cleaning fluid or denatured alcohol. (These cleaning kits are commercially available.)

When cleaning with a cotton swab, wipe the recording/playback head, erasure head (Deck 1 only), capstans, and pinchrollers.

	Recording/
~-asure	playback	Cotton swab
	head	\	~.anetan

(J

\l.—

1. n~n J 1. nmn J

I

1

After cleaning the heads and tape paths with a liquid head cleaning cassette or a moistened swab, wait until the cleaned parts are completely dry before inserting the tapes.

To demagnetize the heads

The heads may become magnetized after long-term use. This may narrow the output range of recorded tapes and increase noise. After 20 to 30 hours use, demagnetize the heads with any. commercially available demagnetizer.

Care of discs

●When a disc becomes dirty, wipe the disc from the center out with a cleaning c

1,

●After piaying a disc, store the disc in its case. Do not leave the disc in piaces that are hot or humid,

Care of tapes

●Store tapes in their cases after use.

●Do not leave tapes near magnets, motors, television sets, or any source of magnetism. This will downgrade the sound quaiity and cause noise.

●Do not expose tapes to direct sunlight, or leave them in a car parked in direct suniight.

~7 ENGLISH

If the unit fails to perform as described in these Operating Instructions, check the following guide.

GENERAL

There is no sound.

●Is’ the AC cord connected properly?

●Is there a bad connection? (+ page 3)

●There may be a short circuit in the speaker terminals.

+Disconnect the AC cord, then correct the speaker connections.

●Was an incorrect function button pressed?

Sound is emitted from one speaker only.

●Is the other speaker disconnected?

An erroneous display or a malfunction occurs. -+ Reset the unit as stated below.

TUNER SECTION

There is constant, wave-like static.

s Is the antenna connected properly? (+ page 4)

●Is the signal weak?

+ Connect an outdoor antenna.

The reception contains noise interferences or the sound is distorted.

●Is the system picking up external noise or multipath distortion? -+ Change the orientation of the antenna.

+ Move the unit away from other electrical appliances.

CASSETTE DECK SECTION

The tape does not run.

●Is the deck in pause mode? (+ page 8)

The sound is off-balance or not adequately high.

●Is the playback head dirty? (+ page 17)

Recording is not possible.

●Is the erasure prevention tab on the tape broken off? (+ page

11)

●is the recording head dirty? (+ page 17)

Erasure is not possible.

●is the erasure head dirty? (+ page 17)

●Is a metal tape being used?

High frequency sound is not emitted.

s Is the recording/playback head dirty? (+ page 17)

CD PLAYER SECTION

The CD player does not play.

●is the disc correctly placed? (- page 9)

●is the disc dirty? (+ page 17)

●Is the lens affected by condensation?

+Wait approximately one hour and try again.

To reset

if an unusuai condition occurs in thedisplay window or the cassette decks, reset the unit as follows.

1Press POWER to turn off the power.

2Press POWER to turn the power back on while pressing ■ CLEAR. Everything stored in memory after purchase is

canceled.

If the power cannot be turned off in step 1 because of a malfunction, reset by disconnecting the AC cord, and connect it again. Then carry out step 2.