Port Status LEDs, Condition Status | Alcatel-Lucent 6300-24 guide

Description of Hardware 1

Status LEDs

The LEDs, which are located on the front panel for easy viewing, are shown below and described in the following table.

Link/Act

BPS

SFP LEDs			FDX
		Figure 1-2. Port LEDs
	Table 1-1. Port Status LEDs

			Port Status LEDs

LED	Condition		Status

RJ-45 Ports

Link/Act.	On Green		Communications have been set to 1000 Mbps.

	On Yellow		Communications have been set to 10/100 Mbps.

	Flashing Green		Traffic is passing through the port at 1000 Mbps.

	Flashing Yellow		Traffic is passing through the port at 10/100 Mbps.

FDX	Green		Communications have been set to full duplex.

	Off		Communications have been set to half duplex.

SFP Transceiver	Slots

(Ports 21-24)	On Green		An SFP transceiver port has established a valid 1000 Mbps
			network connection. The associated RJ-45 port is disabled.
	Off		An SFP transceiver port has no valid link, or the link has
			failed. The associated RJ-45 port is enabled.

1-3

Image 19

Alcatel-Lucent 6300-24 manual Port Status LEDs, Condition Status

Contents

Part No -10, Rev. a December OmniStackPage Page Page Compliances and Safety Warnings Industry Canada Class B Vii Safety ComplianceUnderwriters Laboratories Compliance Statement Warnhinweis Faseroptikanschlüsse Optische Sicherheit Viii Wichtige Sicherheitshinweise Germany Documentation Environmental StatementEnd of Product Life Span Manufacturing Materials Related Publications Purpose Contents Glossary Index Appendix a TroubleshootingAppendix C Specifications Appendix B Cables Tables Tables Xii Figures Figures Xiv Network Management Options Switch ArchitectureIntroduction Overview Introduction Description of Hardware10/100/1000BASE-T Ports SFP Slots Port Status LEDs Status LEDsCondition Status System LEDs System Status LEDs Power Supply Receptacles Optional Backup Power SupplyFeatures and Benefits Management Network Planning Introduction to Switching Collapsed Backbone Application ExamplesNetwork Planning Network Aggregation Plan Network Aggregation Plan Remote Connection with Fiber Cable Remote Connection with Fiber Cable Making Vlan Connections Making Vlan Connections Application Notes Selecting a Site Installing the SwitchEthernet Cabling Package Contents Equipment ChecklistOptional Rack-Mounting Equipment To rack-mount devices MountingRack Mounting Mounting Desktop or Shelf Mounting Installing the Switch in a Rack Installing an Optional SFP Transceiver into the Switch Connecting to a Power Source Power Receptacle Connecting to the Console Port Serial Cable Wiring Switch’s 9-Pin Null Modem PC’s 9-Pin Wiring Map for Serial CableDTE Port Installing the Switch Twisted-Pair Devices Connecting to PCs, Servers, Hubs and SwitchesConnecting Network Devices Making Network Connections Making Network Connections Network Wiring Connections Making LC Port Connections Fiber Optic SFP Devices Mbps Gigabit Ethernet Collision Domain ConnectorConnectivity Rules 1000BASE-T Cable Requirements Mbps Ethernet Collision Domain Mbps Fast Ethernet Collision Domain100 m 328 ft RJ-45 Cable Labeling and Connection Records Installation Appendix a TroubleshootingDiagnosing Switch Indicators Power and Cooling Problems Troubleshooting Twisted-Pair Cable and Pin Assignments Appendix B Cables10BASE-T/100BASE-TX Pin Assignments Cables 1000BASE-T Pin Assignments Fiber Standards B Fiber Standards Cables Physical Characteristics Appendix C Specifications Compliances SpecificationsCE Mark Glossary-1 Glossary Glossary-2 Glossary Glossary-3 LED Glossary Glossary-4 Index-1 Index Index-2 IndexPage 060190-10