Manuals / Alcatel-Lucent / Computer Equipment / Switch

Alcatel-Lucent 6300-24 Equipment Checklist, Package Contents, Optional Rack-Mounting Equipment

Models: 6300-24

1 58

Download 58 pages 48.23 Kb

Page 30

RJ-45 Connector

3 Installing the Switch

RJ-45 Connector

Figure 3-1. RJ-45 Connections

Equipment Checklist

After unpacking the switch, check the contents to be sure you have received all the components. Then, before beginning the installation, be sure you have all other necessary installation equipment.

Package Contents

•Gigabit Ethernet Switch

•Four adhesive foot pads

•Bracket Mounting Kit containing two brackets and eight screws for attaching the brackets to the switch

•Power Cord—either US, Continental Europe or UK

•RS-232 console cable

•This Getting Started Guide

•User Guide

Optional Rack-Mounting Equipment

If you plan to rack-mount the switch, be sure to have the following equipment available:

•Four mounting screws for each device you plan to install in a rack—these are not included

•A screwdriver (Phillips or flathead, depending on the type of screws used)

3-2

Image 30

Alcatel-Lucent 6300-24 manual Equipment Checklist, Package Contents, Optional Rack-Mounting Equipment, RJ-45 Connector

Contents

OmniStack Getting Started GuideThis Manual documents OmniStack 6300-24 hardware and software This equipment has been tested and found to comply with the limits for Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this guide, may cause interference to radio communications. Operation of this equipment in a residential area is likely to cause interference, in which case the user will be required to correct the interference at his own expense Page Compliances and Safety Warnings FCC - Class BEC Conformance Declaration - Class B Industry Canada - Class B Japan VCCI Class BWarning Fiber Optic Port Safety Safety ComplianceUnderwriters Laboratories Compliance Statement Warnhinweis Faseroptikanschlüsse - Optische SicherheitWichtige Sicherheitshinweise Germany End of Product Life Span Warnings and Cautionary MessagesEnvironmental Statement Manufacturing MaterialsPurpose Related PublicationsThe OmniStack 6300 User Guide Contents Appendix B Cables Appendix A TroubleshootingAppendix C Specifications Glossary IndexTables Tables Figures Figures Overview Switch ArchitectureChapter 1 Introduction Network Management OptionsDescription of Hardware 10/100/1000BASE-T PortsSFP Slots Table 1-1. Port Status LEDs Status LEDsFigure 1-2. Port LEDs ConditionPower Indicator Redundant Power IndicatorDiagnostic Indicator Optional Backup Power Supply Power Supply ReceptaclesFeatures and Benefits Management “At-a-glance” LEDs for easy troubleshooting Network management agentManages switch in-band or out-of-band Supports Telnet, SNMP/RMON and Web-based interfaceIntroduction to Switching Chapter 2 Network PlanningApplication Examples Collapsed BackboneNetwork Aggregation Plan Figure 2-2. Network Aggregation PlanRemote Connection with Fiber Cable Figure 2-3. Remote Connection with Fiber CableMaking VLAN Connections Figure 2-4. Making VLAN ConnectionsApplication Notes Chapter 3 Installing the Switch Selecting a SiteEthernet Cabling Optional Rack-Mounting Equipment Equipment ChecklistPackage Contents RJ-45 ConnectorMounting Rack MountingDesktop or Shelf Mounting Figure 3-3. Installing the Switch in a RackFigure 3-4. Attaching the Adhesive Feet Connecting to a Power Source Installing an Optional SFP Transceiver into the SwitchConnecting to the Console Port Figure 3-6. Power ReceptacleFigure 3-7. Serial Port DB-9 DTE Pin-Out Switch’s 9-Pin Wiring Map for Serial CableTable 3-1. Serial Cable Wiring Null Modem3 Installing the Switch Chapter 4 Making Network Connections Connecting to PCs, Servers, Hubs and SwitchesConnecting Network Devices Twisted-Pair DevicesNetwork Wiring Connections Figure 4-2. Network Wiring ConnectionsFiber Optic SFP Devices Figure 4-3. Making LC Port ConnectionsConnectivity Rules 1000BASE-T Cable Requirements1000 Mbps Gigabit Ethernet Collision Domain 100 Mbps Fast Ethernet Collision Domain 10 Mbps Ethernet Collision DomainCategory 5 or better 100-ohm UTP or STP Cable Labeling and Connection Records Power and Cooling Problems Appendix A TroubleshootingDiagnosing Switch Indicators InstallationA Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments 1000BASE-T Pin Assignments Cable Testing for Existing Category 5 CableFiber Standards Adjusting Existing Category 5 Cabling to Run 1000BASE-TB Cables Appendix C Specifications Physical CharacteristicsCompliances CE MarkGlossary Glossary Glossary-2Local Area Network LAN Glossary Glossary-4Index NumericsPage Page 060190-10