E:OPERATION AND ADJUSTMENT INSTRUCTIONS

Adjustment #5: Alignment and Initial Test of Safe Finish Photosystem

A.Keep a portable transmitter with you to control the garage door opener. The red light on the receiver unit should now be on. If not, recheck that the mounting screws are tight then, if necessary, align the photosystem by slightly bending the wall bracket until proper operation is obtained.

B.Place an object (packing insert box or a similar object approximately six inches high) one foot in front of the transmitter or receiver. The red LED should go OFF and remain OFF until the object is removed. NOTE: There may be a slight delay in returning to normal depending upon how long the photosystem was blocked. If the light fails to go off when the object is placed in the path of the beam check the wire connections and the installation height of the units (see Page 13).

C.Move to the center of the door. Make sure the red LED light is on. Move a solid object slowly through the beam. The LED should go OFF and then ON.

D.Using the pushbutton or transmitter, activate the opener and check that it will operate through the full open and close cycles. If not, re-align the photosystem by slightly bending the wall bracket until proper operation is obtained.

E.Tighten all mounting screws and bolts, loop and secure any extra wire.

Important Test: Photoelectric Obstruction Test

Test Procedure

 

 

 

 

 

 

 

Place an object 6” x 12” on the floor (as illustrated)

 

 

 

 

 

 

 

progressively on foot from the left side of the door; center of

 

 

 

 

 

 

 

the door and one foot from the right side of the door. The

 

 

 

 

 

 

 

object must prevent an open door from closing in any other

 

 

 

 

 

 

 

mode other than constant pressure on the wall button. The

 

 

 

 

 

 

 

object should also cause a closing door stop and reverse to

 

 

 

 

 

 

 

the open position. If it doesn’t, the Safe Finish photoelectric

 

 

 

 

 

 

 

system must be adjusted lower and the test repeated until the

 

 

 

 

 

 

 

door responds properly to the 6” object.

 

 

 

 

 

 

 

 

Garage Door

 

 

If adjustments are needed, refer to preceding adjustment.

 

 

Opening

 

 

 

 

 

 

 

 

 

 

If the unit still will not respond and fails this obstruction

 

 

 

 

 

 

 

sensing beam test, the door may cause severe injury or death.

 

 

 

 

 

 

6”

 

 

 

 

12”

 

 

 

 

 

 

Have a qualified service person make repairs.

 

 

 

 

 

 

 

12”

 

 

Adjustment #6: Positive Mechanical Lock Adjustment

 

 

 

 

 

 

 

 

 

 

 

 

Rail “Stop”

 

 

 

 

 

 

 

 

 

 

 

 

The garage door opener is designed with an automatic mechanical

 

 

1/2”

“Latch”

 

 

 

 

 

 

 

 

 

 

 

 

 

locking system. This lock secures the door in the fully closed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

position.

 

 

 

 

 

 

 

To adjust, activate your opener and allow the door to go to its

 

 

 

 

 

 

 

fully closed position. Loosen the two screws on the rail stop

 

 

 

 

 

 

 

and move it behind behind the chain latch assembly with a gap

 

 

 

 

 

 

 

of 1/2” between “stop” and “latch”.

 

 

 

 

 

 

 

Adjustment #7 :Resetting the Travel Timer

 

 

 

 

 

 

 

 

 

110057-2

 

 

 

Your opener is shipped with the jumper connected, allowing the operator to run continuously for 17 seconds, then stop in the Open cycle or reverse in the closing cycle, activating the flashing light mode.

On all doors having over 9 feet of travel, it is necessary to cut the run timer jumper on the motor control board to allow the opener to run for 29 seconds. Disconnect the power from the opener before removing cover and cutting the jumper. MAKE SURE YOU DISCONNECT THE POWER BEFORE CUTTING THE JUMPER. THE RUN TIMER WILL NOT CHANGE IF THE JUMPER IS CUT WITH THE POWER CONNECTED.

This jumper is located under operator cover on the control board, as illustrated.

110055-2

Sensor

12”

Stop Limits

110057-1

Cut and

Separate

19

Page 18 Page 20
Page 19
Image 19
Allstar Products Group ACJ9500 Important Test Photoelectric Obstruction Test, Adjustment #7 Resetting the Travel Timer
Page 18 Page 20

AC9300, AC9500, ACJ9500 specifications

Allstar Products Group has established a strong reputation in the field of automotive accessories, and their line of ACJ9500, AC9500, and AC9300 models exemplifies this commitment to quality and functionality. These units are designed to cater to a wide range of needs, enhancing vehicle performance and user convenience.

The ACJ9500 is particularly noteworthy for its impressive power output and versatility. It is equipped with a robust motor that delivers efficient performance, making it suitable for various applications, from automotive work to home improvement tasks. One of its standout features is the adjustable speed setting, allowing users to customize the airflow according to their specific needs. This model also includes a durable construction that ensures longevity, even under demanding conditions.

Moving on to the AC9500, this unit is celebrated for its compact design, which does not compromise on power or efficiency. It is lightweight and portable, making it an ideal choice for individuals who require a reliable tool that can be easily transported. The AC9500 is equipped with user-friendly controls that simplify operation, ensuring that even those with minimal experience can quickly get the hang of it. Its noiseless operation is another significant advantage, perfect for environments where quiet is essential.

The AC9300 model rounds out the lineup with its emphasis on energy efficiency. This unit utilizes cutting-edge technology, which minimizes power consumption while maintaining optimal performance. It is specifically designed to reduce energy waste, making it an environmentally friendly option for customers who are conscious of their ecological footprint. The AC9300 also features a unique ventilation system that enhances airflow, promoting better circulation and cooling, which is especially valuable in automotive applications.

In summary, the Allstar Products Group models ACJ9500, AC9500, and AC9300 deliver a combination of power, efficiency, and user-friendly features that cater to diverse needs. Their innovative technologies and durable designs showcase Allstar’s commitment to providing high-quality automotive accessories. Each model stands out for its specific strengths, making them suitable for different tasks and environments. Whether for professional or personal use, these models continue to meet the demands of consumers looking for reliability and performance in automotive tools. The combination of functionality and practicality ensures that Allstar's offerings remain competitive in the market.
Top Page Image Contents