Restore System Default Settings, Reboot System | Linksys SGE2010

Using the Console

System Configuration

Restore System Default Settings

You can restore the switch to the system default settings.

To restore system default settings

1.From the Switch Main Menu, select 1. System Configuration.

2.From the System Configuration Menu, select 8. Restore System Default Settings.

3.When the confirmation message appears, press y to restore the default settings, or press n to cancel.

NOTE: Restoring default settings from the console or web resets all values except stacking configuration (stacking mode, stacking ports, and auto-numbering settings are not reset). To reset stacking configuration, use the hardware reset button on the front of the Ethernet switch.

Reset to Factory Settings

You can restore the switch to the factory default settings.

To restore factory default settings

1.From the Switch Main Menu, select 1. System Configuration.

2.From the System Configuration Menu, select 9. Restore Factory Settings.

3.When the confirmation message appears, press y to restore the default settings, or press n to cancel.

NOTE: Restoring factory settings from the console or web resets all values except stacking configuration (stacking mode, stacking ports, and auto-numbering settings are not reset). To reset stacking configuration, use the hardware reset button on the front of the Ethernet switch.

Reboot System

You can restart the Ethernet switch.

To restore system default settings

1.From the Switch Main Menu, select 1. System Configuration.

2.From the System Configuration Menu, select 10. Reboot System.

3.When the confirmation message appears, press y to restore the default settings, or press n to cancel.

SGE2010/SGE2010P Administration Guide

43

Image 46

Linksys SGE2010P manual Restore System Default Settings, Reset to Factory Settings, Reboot System

Contents

Port 10/100/1000 Ethernet Switch Table of Contents Contacts Introduction What’s in this User Guide? Getting to Know the SGE2010/SGE2010P SGE2010/P Front Panel Getting to Know the SGE2010/SGE2010P SGE2010/P Back Panel Sample Network Configuration Maximum Cabling Distances Placement Options Before You Install the SwitchDesktop Placement Rack-Mount Placement Connecting the Cables Wall-Mount Placement Connecting Devices to the SGE2010/SGE2010P Using the Console Connecting to Your Switch with HyperTerminal Using the Console Set the serial port settings as follows Logging On to the Console Connecting to the Switch with TelnetSelecting Menu Options and Actions Using the Switch Main Menu System Configuration To open this screen System InformationTo open this menu Versions General Information Management Settings To change the system contact, system name, and location Telnet Configuration Serial Port ConfigurationTo change the baud rate of the serial port SSH Configuration To change the time-out setting SSH Server Configuration To change SSH Server settings To change SSH Crypto Key Generation settings Username & Password Settings To generate the crypto key Security Settings To change User & Password settings SSL Generate Certificate To edit and execute a certificate To disable the active management access profile Disable Active Management Access ProfileShow Certificate Default Vlan Setup Vlan Management IP Configuration To edit the Vlan ID IPv4 Address Configuration To edit the IPv4 address settings IPv6 Address ConfigurationTo renew Dhcp To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings IPv6 Default Gateway To edit the IPv6 default gateway settings To change the Http settings Http ConfigurationHttps Configuration To open the screen Network Configuration To change Https settings To change the IP address To begin the ping test Ping IPv6 To begin the trace route test TraceRoute IPv6 Upgrade / Backup IPv4 File Management To enter the IPv6 Upgrade/Backup file name and location Upgrade / Backup IPv6To enter the IPv4 Upgrade/Backup file name and location To download a file from the specified location To enter the active image settings Active Image Reboot System Restore System Default SettingsReset to Factory Settings To restore system default settings Stack Configuration Port Status Port Status PoE Status Port Configuration Port Settings PoE Settings To configure the ports System Mode Layer 2 / Layer 3 Selection To configure the PoE settings To edit the system mode or stacking mode Help Logout Connecting to the Switch with the Web-Based Utility Using Menus in the Web-Based Utility Viewing On-line Help US/Canada Contacts EU Contacts Customer Site Survey Yes Limited Warranty Exclusions and Limitations Obtaining Warranty Service Technical Support Obtaining Warranty Service Industry Canada Statement EC Declaration of Conformity Europe Specifications Radius Vlan EMC 080312A-LB