Connecting Devices to the SGE2010/SGE2010P | Linksys instruction

Connecting Devices to the SGE2010/SGE2010P

Connecting the Cables

CAUTION: Observe the orientation of the mini-GBIC module before inserting it into a mini- GBIC port. The bottom mini-GBIC ports are upside down in relation to the top mini-GBIC ports.

5.If you use the console interface to configure the Ethernet switch, then connect the supplied serial cable to the console port (located on the back of the Ethernet switch), and tighten the captive retaining screws. Connect the other end to your PC’s serial port. (The PC must be running VT100 terminal emulation software, such as HyperTerminal.)

6.Connect the supplied power cord to the power port, and plug the other end into an electrical outlet.

CAUTION: Make sure you use the power cord that is supplied with the Ethernet switch. Use of a different power cord could damage the Ethernet switch.

7.Power on the network devices connected to the Ethernet switch. Each active port’s corresponding Act/Link LED will light up on the Ethernet switch. If a port has an active Gigabit connection, then its corresponding Gigabit LED will also light up.

8.Proceed as needed:

•If you will use the console interface to configure the Ethernet switch, proceed to ”Console Configuration” section on page 33 for directions.

•If you use the Web-based Utility to configure the Ethernet switch, proceed to ”Web Utility Configuration” section on page 50.

SGE2010/SGE2010P Administration Guide

8

Image 11

Linksys manual Connecting Devices to the SGE2010/SGE2010P

Contents

Port 10/100/1000 Ethernet Switch Table of Contents Contacts What’s in this User Guide? Introduction SGE2010/P Front Panel Getting to Know the SGE2010/SGE2010P SGE2010/P Back Panel Getting to Know the SGE2010/SGE2010P Maximum Cabling Distances Sample Network Configuration Desktop Placement Before You Install the SwitchPlacement Options Rack-Mount Placement Wall-Mount Placement Connecting the Cables Connecting Devices to the SGE2010/SGE2010P Connecting to Your Switch with HyperTerminal Using the Console Using the Console Set the serial port settings as follows Selecting Menu Options and Actions Connecting to the Switch with TelnetLogging On to the Console System Configuration Using the Switch Main Menu To open this menu System InformationTo open this screen General Information Versions To change the system contact, system name, and location Management Settings To change the baud rate of the serial port Serial Port ConfigurationTelnet Configuration To change the time-out setting SSH Configuration To change SSH Server settings SSH Server Configuration To change SSH Crypto Key Generation settings To generate the crypto key Username & Password Settings To change User & Password settings Security Settings To edit and execute a certificate SSL Generate Certificate Show Certificate Disable Active Management Access ProfileTo disable the active management access profile Vlan Management Default Vlan Setup To edit the Vlan ID IP Configuration IPv4 Address Configuration To renew Dhcp IPv6 Address ConfigurationTo edit the IPv4 address settings To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings To edit the IPv6 default gateway settings IPv6 Default Gateway To open the screen Http ConfigurationHttps Configuration To change the Http settings To change Https settings Network Configuration To begin the ping test To change the IP address Ping IPv6 To begin the trace route test TraceRoute IPv6 File Management Upgrade / Backup IPv4 To download a file from the specified location Upgrade / Backup IPv6To enter the IPv4 Upgrade/Backup file name and location To enter the IPv6 Upgrade/Backup file name and location Active Image To enter the active image settings To restore system default settings Restore System Default SettingsReset to Factory Settings Reboot System Port Status Stack Configuration PoE Status Port Status Port Settings Port Configuration To configure the ports PoE Settings To configure the PoE settings System Mode Layer 2 / Layer 3 Selection Help To edit the system mode or stacking mode Logout Using Menus in the Web-Based Utility Connecting to the Switch with the Web-Based Utility Viewing On-line Help EU Contacts US/Canada Contacts Customer Site Survey Yes Exclusions and Limitations Limited Warranty Obtaining Warranty Service Obtaining Warranty Service Technical Support EC Declaration of Conformity Europe Industry Canada Statement Specifications Radius Vlan EMC 080312A-LB