Industry Canada Statement | Linksys SGE2010P instruction

D

Federal Communication

Commission Interference

Statement

This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Industry Canada Statement

The Class [A] digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulation. Cet appareil numerique de la class [A] respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.

EC Declaration of Conformity (Europe)

In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, and Amendment Directive 93/68/EEC, this product meets the requirements of the following standards:

•EN55022 Emission

•EN55024 Immunity

SGE2010/SGE2010P Administration Guide

58

Image 61

Linksys SGE2010P manual Industry Canada Statement, EC Declaration of Conformity Europe

Contents

Port 10/100/1000 Ethernet Switch Table of Contents Contacts What’s in this User Guide? Introduction SGE2010/P Front Panel Getting to Know the SGE2010/SGE2010P SGE2010/P Back Panel Getting to Know the SGE2010/SGE2010P Maximum Cabling Distances Sample Network Configuration Placement Options Before You Install the SwitchDesktop Placement Rack-Mount Placement Wall-Mount Placement Connecting the Cables Connecting Devices to the SGE2010/SGE2010P Connecting to Your Switch with HyperTerminal Using the Console Using the Console Set the serial port settings as follows Logging On to the Console Connecting to the Switch with TelnetSelecting Menu Options and Actions System Configuration Using the Switch Main Menu To open this screen System InformationTo open this menu General Information Versions To change the system contact, system name, and location Management Settings Telnet Configuration Serial Port ConfigurationTo change the baud rate of the serial port To change the time-out setting SSH Configuration To change SSH Server settings SSH Server Configuration To change SSH Crypto Key Generation settings To generate the crypto key Username & Password Settings To change User & Password settings Security Settings To edit and execute a certificate SSL Generate Certificate To disable the active management access profile Disable Active Management Access ProfileShow Certificate Vlan Management Default Vlan Setup To edit the Vlan ID IP Configuration IPv4 Address Configuration To edit the IPv4 address settings IPv6 Address ConfigurationTo renew Dhcp To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings To edit the IPv6 default gateway settings IPv6 Default Gateway Https Configuration Http ConfigurationTo change the Http settings To open the screen To change Https settings Network Configuration To begin the ping test To change the IP address Ping IPv6 To begin the trace route test TraceRoute IPv6 File Management Upgrade / Backup IPv4 To enter the IPv4 Upgrade/Backup file name and location Upgrade / Backup IPv6To enter the IPv6 Upgrade/Backup file name and location To download a file from the specified location Active Image To enter the active image settings Reset to Factory Settings Restore System Default SettingsReboot System To restore system default settings Port Status Stack Configuration PoE Status Port Status Port Settings Port Configuration To configure the ports PoE Settings To configure the PoE settings System Mode Layer 2 / Layer 3 Selection Help To edit the system mode or stacking mode Logout Using Menus in the Web-Based Utility Connecting to the Switch with the Web-Based Utility Viewing On-line Help EU Contacts US/Canada Contacts Customer Site Survey Yes Exclusions and Limitations Limited Warranty Obtaining Warranty Service Obtaining Warranty Service Technical Support EC Declaration of Conformity Europe Industry Canada Statement Specifications Radius Vlan EMC 080312A-LB