INPUT/OUTPUT I/O Board L.E.D. Indicators | American Dryer Corp None

C. INPUT/OUTPUT (I/O) BOARD L.E.D. INDICATORS

1.Top Pocket Inputs H2O – (RED L.E.D.)

LINT – (RED L.E.D.)

EXHL – (RED L.E.D.)

SAIL – (RED L.E.D.)

GAS_V – (RED L.E.D.)

MAIN – (RED L.E.D.)

FUSE – (RED L.E.D.)

BRHL – (RED L.E.D.)

2.Top Pocket Outputs HEAT – (GREEN L.E.D.)

DRIVE – (GREEN L.E.D.)

FAN – (GREEN L.E.D.)

FSS – (GREEN L.E.D.)

This light emitting diode (L.E.D.) will indicate the status of the water pressure sensor. If the water pressure is present, the L.E.D. will be ON.

This L.E.D. will indicate the status of the lint drawer. If the drawer is closed, then the L.E.D. is ON.

This L.E.D. will indicate the status of the exhaust high limit disk. If the disk is closed (temperature below 225º F [107º C]), then the L.E.D. is ON.

This L.E.D. will indicate the status of the sail switch. If the switch is closed, then the L.E.D. is ON.

This L.E.D. will indicate the status of the gas valve. If the gas valve is open (ON), then the L.E.D. is ON.

This L.E.D. will indicate the status of the main door. If the door is closed, then the L.E.D. is ON.

This L.E.D. should be on at ALL times. If L.E.D. is off this will indicate that fuse # F1 is blown.

This L.E.D. will indicate the status of the burner high limit disk. If the disk is closed (temperature below 330º F [166º C]), then the L.E.D. is ON.

This L.E.D. will indicate the status of the heat output. If the request to turn on the heater is made, then the L.E.D. is ON.

This L.E.D. will indicate the status of the basket (tumbler) forward direction output. If the request to tumble the basket (tumbler) in the forward direction is made, then the L.E.D. is ON.

This L.E.D. will indicate the status of the fan output. If the request to turn on the fan (blower) is made, then the L.E.D. is ON.

This L.E.D. will indicate that the S.A.F.E. system is active.

70

Image 72

American Dryer Corp None INPUT/OUTPUT I/O Board L.E.D. Indicators, Drive Green L.E.D FAN Green L.E.D FSS Green L.E.D

Contents

DMC Retain This Manual In a Safe Place For Future Reference Important Note to Purchaser Table of Contents Section Phase 7 Dual Microprocessor Controller DMC Computer Section Features Keyboard Touch Pad Symbols = PAUSE/CLEAR key Coin Mode Free Mode HOT Keys Pause Mode Scrolling RateRPM Accessing Coin Vault Clearing Fault Records and CreditClearing CREDIT/CLEARING Cycle Wrinkle Guard A.F.E. System D. Operating Messages Messages Common to Coin and Free Modes Select Temp to Start Close Lint Access Select Buzzer Mode Select DRY ModeSelect Language Select Temp Scale Select Rotation Sensor Mode Enter Lint Cleaning Frequency 0 to 10 HoursPause Time 0 to 3 Minutes Ready Prompt Coin Mode Free ModeAxial Thermistor Input Thermistor Temp SET Point 100 to 400F Currency Symbol Time for TOP OFF 1 to 99 MinutesEnter High DRY Temp 100 to 190F Cool Time 0 to 9 Minutes Select Vending Mode Accumulative Time Dual CoinAcceptor Accumulative Coin Dual CoinAcceptor Select Vending Safeguard No FaultsFaults Enter LEFT/RIGHT Coin Denomination 0.05 to Programming Instructions Introduction to Programming Program Location Summary Programming Flowcharts MED Flowchart Table of Contents Program Mode Control Settings Select Language English Spanish Temp ScaleSelecting Display Language READY, Insert Control Settings Select Language Select Temp Scale Select Buzzer ModeSelecting Temp Scale Selecting Buzzer Mode Control Settings Select Language Buzzer ModeOFF Count Control Settings Select Language Beep Count 1 to 9 Beeps Select DRY ModeSelecting Beep Count Selecting DRY Mode Free DRY ModeSelect Pause Time 0 to Minutes Selecting Pause Time Select Language Pause Time 0 to Minutes Select Ready Prompt Selecting Ready Prompt ReadyMachine Machine Settings Select Model Type GAS Single Motor Selecting Model TypeElectric Single Motor Rotation Setting Rotation Sensor Setting Lint Cleaning Frequency Settings AxialLint Cleaning Frequency 0 to Hours Machine Setting Axial Thermistor Input OFFTemp Setpoint Axial Thermistor Input Setting Thermistor Temp SET Point Thermistor Temp HI KEY- Setting Time for Amount to Start HI KEY- Setting Time for TOP OFF Time for TOPTime for TOP OFF To 99 Minutes HI KEY- Setting DRY Temp 100 to 190 F PL #03 HI KEY SettingsTime for Amount to Start 1 to Minutes Cool Time 0 to Minutes HI KEY- Setting Cool Time 0 to 9 Minutes PL#04 MED KEY Settings MED KEY- Setting Time for Amount to Start PL #01 Control SettingsPL #04 MED KEY Settings Time for Amount to Start 1 to Minutes MED KEY- Setting Time for TOP OFF MED KEY- Setting DRY Temp 100 to 190 F Cool Time 0 to Minutes MED KEY- Setting Cool Time 0 to 9 Minutes PL #05 LO KEY Settings LO KEY- Setting Time for Amount to Start LO KEY- Setting Time for TOP OFF Time for TOP OFF To 99 Minutes LO KEY- Setting DRY Temp 100 to 190 F LO KEY- Setting Cool Time 0 to 9 Minutes PL #06 Vending Parameters Selecting Currency Symbol Vending Mode Selecting Vending Mode Selecting Vending Safeguard Setting Left Coin Denomination Control Settings PL #06 Vending Setting Right Coin Denomination Amount to Start 0.05 to Setting Amount to Start Amount forTOP OFF 0.05 to Setting Amount for TOP OFF 0.05 to PL#07 Fault RecordingAmount for TOP OFF Accessing Upper Dryer Fault Records PL #01 Control SettingsPL #07 Fault Recording Upper Dryer Faults Accessing Lower Dryer Fault Records PL #01 Control Settings PL #07 Fault RecordingLower Dryer Faults Flowchart for Clearing Credit Accessing and Clearing Coin Vault Total YES Factory Defaults HI KEY SettingsMED KEY Settings LO KEY Settings Control Settings Language Fault Recording READY-INSERT Amount to StartUSD Diagnostic L.C.D. Fault Messages Error MessagesStandards Page Page Page A.F.E. System Diagnostic Conditions INPUT/OUTPUT I/O Board L.E.D. Indicators Drive Green L.E.D FAN Green L.E.D FSS Green L.E.D Lint RED L.E.D Keyboard Touch PAD Layout Page ADC Part No 10/01/08