Manuals / American Dryer Corp / Laundry Appliance / Clothes Dryer

American Dryer Corp WDA-385 service manual H. Tumbler basket Tumbler Alignment vertical

Models: WDA-385

1 57

Download 57 pages 20.54 Kb

Page 37

H. Tumbler (basket)

H. Tumbler (basket)

Tumbler Alignment (vertical)

1. Discontinue power to dryer.

2. Remove backguard.

3. Loosen the four (4) hex head bolts on the sides of the bearing box (2 on each side).

4. Back off jam nuts on the two (2) allen head adjustment screws.

5. Turn the screws clockwise evenly to raise the number or counter clockwise evenly to lower the number.

6.Rotate the tumbler from the front and check alignment with the main door opening.

7.Leave a large gap from the inside ring on

the top of the front panel opening to the tumbler, and a smaller gap on the bottom to compensate for the weight of the clothes drying.

8. Tighten the four (4) hex head bolts on the sides of the bearing box, and the two (2) allen head adjustment screws.

9. Replace backguard.

10. Reconnect power to dryer.

Tumbler Alignment (lateral)

1. Discontinue power to dryer.

2. Remove backguard.

3.Loosen the two (2) hex head bolts, (one turn is enough), that holds the pillow block bearings to the bearing box.

4.Back off the two (2) jam nuts on the side adjustment bolts. Now rotate the tumbler from the front of the dryer, checking the space between the tumbler and the front panel. This should be equal on the left hand and right hand side.

33

Image 37

American Dryer Corp WDA-385 service manual H. Tumbler basket Tumbler Alignment vertical, Tumbler Alignment lateral

Contents

ADG-385/WDA-385 Service Manual1996 thru 121396MFM/tf“IMPORTANT NOTE TO PURCHASER” Retain This Manual In A Safe Place For Future ReferenceDRYERS SHOULD NEVER BE LEFT UNATTENDED WHILE IN OPERATION VERIFY PROPER OPERATION AFTER SERVICINGCHILDREN SHOULD NOT BE ALLOWED TO PLAY ON OR NEAR THE DRYERS CHILDREN SHOULD BE SUPERVISED IF NEAR DRYERS IN OPERATIONFOR YOUR SAFETY Maintenance Table of ContentsInstallation Requirements Important InformationTechnical Information Trouble ShootingSECTION A. Safety PrecautionsImportant Information A. Cleaning Routine MaintenanceSECTION C. Lubrication B. AdjustmentsA. Enclosure, Air Supply, and Exhaust Requirements Installation RequirementsSECTION B. Electrical and Gas Requirements C. Operational Service Check ProcedurePage A. Control Panel Description of PartsB. Control Box C. Coin Box and VaultE. Lint Coop D. Main Door SwitchF. Tumbler G. Tumbler Bearing and Pulley Arrangement I. Motor AssemblyH. Idler Bearing K. Sail Switch J. Temperature SensorsM. Non-Reversing Contactor 3Ø Motor L. Motor Contactor 1Ø MotorN. Hi-Limit Thermostat Servicing To Replace Control Panel AssemblySECTION To Replace Keypad refer to illustration above To Replace ComputerTo Replace Coin Acceptor To Remove Optic SwitchTo Replace Motor Contactor 2-Pole, 24VAC To Replace Microprocessor Temperature Sensor ProbeNOTE DO NOT remove screws A. Burner Controls Gas To Replace Gas Valve To Replace Spark IgnitorTo Test and Adjust Gas Water Column Pressure To Replace Main Burner Orifices See Chart On Following PageNEVER TEST FOR LEAKS WITH A FLAME To Replace Burner TubesTo Replace DSI Module B. Thermostats and Temperature SensorTo Replace Hi-Limit Thermostat 330º To Remove The Temperature Sensor or High Heat Protector To Replace Sail Switch C. Sail Switch AssemblyTo Replace Main Door Switch Steel Door To Adjust Sail SwitchD. Front Panel and Main Door Assemblies TO REPLACE MAIN DOOR ASSEMBLY STEEL DOORTO INSTALL NEW MAIN DOOR GLASS NOTE Identify location of each wire for correct reinstallation To Replace Front PanelTo Replace Tumbler Pulley E. Tumbler and Bearing Assembly Remove backguard to access assemblyNOTE Check belt alignment before operating dryer IMPORTANT LOCTITE NOW BEING USED To Replace Rear Tumbler BearingNOTE Check alignment of pulleys before operating dryer To Replace The Front Tumbler Bearing To Replace Idler Pulley F. Idler and Bearing AssemblyRemove backguard to access assembly NOTE Check tension and alignment of belts before operating dryerG. Drive Pulley To Replace Idler BearingTumbler Alignment lateral H. Tumbler basket Tumbler Alignment verticalNOTE Identify location of each wire for correct re-installation To Replace The Tumbler and/or Tumbler SupportLOCTITE ADHESIVE HAS BEEN USED TO SECURE SET SCREWS AND BEARINGS IMPORTANT LOCTITE NOW BEING USEDIN PLACE. ONCE SET SCREWS HAVE BEEN REMOVED, A GEAR PULLER MAY BE NECESI. V-Belts refer to illustration in Sections I, J and K V-Belt Tension Adjustment-Tumbler To IdlerV-Belt Tension Alignment - Motor To Idler J. Motor To Replace Motor To Replace V-BeltsK. Impeller L. Lintscreen To Replace LintscreenA. Phase 5 Coin System Diagnostics Trouble ShootingDiagnostic L.E.D. Display Failure Codes SECTIONMicroprocessor Controller Relay Output L.E.D. Indicators L.E.D. Display IndicatorsNOTE If the dryer is started the L.E.D. display indicator dots are on and there are no outputs heat and/or motor output L.E.D.s are off and the dOOr input L.E.D. is on, the fault is in the Phase 5 coin microprocessor controller computer itself. If the failure was elsewhere i.e., dryers door switch circuit the L.E.D. display would read dOOr if a keyboard entry was attempted. If the L.E.D. display indicators are on and the door L.E.D. input and motor/heat output L.E.D.s are on and the motor and/or heat is not active ON, then the problem is not the door switch circuit or the Phase 5 coin microprocessor controller the problem is else where in the dryer B. No Heat Condition Page C. No Start Condition D. No Display Condition Page E. dSFL Display Condition F. dOOr Display Condition A. Data Label Technical InformationSECTION B. Using A Manometer C. L.E.D. Display Codes D. Computer Logic and Wiring Diagram including ALL revisions of the number listed below B672611 Diagrams for this book are as follows1- 01/08/98-50 ADC4501792* 05/21/98-50