Manuals / American Dryer Corp / Laundry Appliance / Clothes Dryer

American Dryer Corp WDA-385 Important Loctite Now Being Used, In Place. Once Set Screws Have Been

Models: WDA-385

1 57

Download 57 pages 20.54 Kb

Page 39

Manual background

IMPORTANT: LOCTITE® NOW BEING USED.

Effective January 24, 1996, LOCTITE® is being used on the ADG-385/WDA-385 dryer. LOCTITE® is being applied toALL beaaring set screws, used onALL basket (tumbler) shafts, ALL idler shafts,ALL impellor (fan/ blower) shafts, and ALL drive shaft bearings.

A yellow label (ADC Part No. 112801) is affixed to the dryer to inform customers of the use of LOCTITE®. This label is shown immediately below;

IMPORTANT

LOCTITE® ADHESIVE HAS BEEN USED

TO SECURE SET SCREWS AND BEARINGS

IN PLACE. ONCE SET SCREWS HAVE BEEN

REMOVED, A GEAR PULLER MAY BE NECES-

SARY TO REMOVE BEARING TO AVOID DAMAGE.

P/N: 112801

One (1) of these labels is attached to each Tumbler (basket) Bearing Assembly (pillow block bearing box) on the ADG-385/WDA-385 dryer.

Should readjustment or removal of set screws become necessary in the field and the process becomes difficult, apply heat to the set screw with a soldering gun (450º F) for a few minutes.

4. Using a wheel puller gently push the tumbler shaft towards the front through the front tumbler bearing.

NOTE: An alternate methodwould be to place a block of wood on the end of the tumbler shaft and strike it with a heavy hammer. To prevent damage to the shaft, the wheel puller method is preferred.

35

Image 39

American Dryer Corp WDA-385 service manual Important Loctite Now Being Used, In Place. Once Set Screws Have Been

Contents

121396MFM/tf Service ManualADG-385/WDA-385 1996 thru“IMPORTANT NOTE TO PURCHASER” Retain This Manual In A Safe Place For Future ReferenceCHILDREN SHOULD BE SUPERVISED IF NEAR DRYERS IN OPERATION VERIFY PROPER OPERATION AFTER SERVICINGDRYERS SHOULD NEVER BE LEFT UNATTENDED WHILE IN OPERATION CHILDREN SHOULD NOT BE ALLOWED TO PLAY ON OR NEAR THE DRYERSFOR YOUR SAFETY Important Information Table of ContentsMaintenance Installation RequirementsTechnical Information Trouble ShootingA. Safety Precautions SECTIONImportant Information Routine Maintenance A. CleaningSECTION C. Lubrication B. AdjustmentsInstallation Requirements A. Enclosure, Air Supply, and Exhaust RequirementsSECTION B. Electrical and Gas Requirements C. Operational Service Check ProcedurePage C. Coin Box and Vault Description of PartsA. Control Panel B. Control BoxD. Main Door Switch E. Lint CoopF. Tumbler I. Motor Assembly G. Tumbler Bearing and Pulley ArrangementH. Idler Bearing K. Sail Switch J. Temperature SensorsL. Motor Contactor 1Ø Motor M. Non-Reversing Contactor 3Ø MotorN. Hi-Limit Thermostat To Replace Control Panel Assembly ServicingSECTION To Replace Keypad refer to illustration above To Replace ComputerTo Replace Coin Acceptor To Remove Optic SwitchTo Replace Microprocessor Temperature Sensor Probe To Replace Motor Contactor 2-Pole, 24VACNOTE DO NOT remove screws A. Burner Controls Gas To Replace Gas Valve To Replace Spark IgnitorTo Test and Adjust Gas Water Column Pressure To Replace Main Burner Orifices See Chart On Following PageNEVER TEST FOR LEAKS WITH A FLAME To Replace Burner TubesB. Thermostats and Temperature Sensor To Replace DSI ModuleTo Replace Hi-Limit Thermostat 330º To Remove The Temperature Sensor or High Heat Protector To Replace Sail Switch C. Sail Switch AssemblyTO REPLACE MAIN DOOR ASSEMBLY STEEL DOOR To Adjust Sail SwitchTo Replace Main Door Switch Steel Door D. Front Panel and Main Door AssembliesTO INSTALL NEW MAIN DOOR GLASS NOTE Identify location of each wire for correct reinstallation To Replace Front PanelE. Tumbler and Bearing Assembly Remove backguard to access assembly To Replace Tumbler PulleyNOTE Check belt alignment before operating dryer To Replace Rear Tumbler Bearing IMPORTANT LOCTITE NOW BEING USEDNOTE Check alignment of pulleys before operating dryer To Replace The Front Tumbler Bearing NOTE Check tension and alignment of belts before operating dryer F. Idler and Bearing AssemblyTo Replace Idler Pulley Remove backguard to access assemblyG. Drive Pulley To Replace Idler BearingTumbler Alignment lateral H. Tumbler basket Tumbler Alignment verticalNOTE Identify location of each wire for correct re-installation To Replace The Tumbler and/or Tumbler SupportREMOVED, A GEAR PULLER MAY BE NECES IMPORTANT LOCTITE NOW BEING USEDLOCTITE ADHESIVE HAS BEEN USED TO SECURE SET SCREWS AND BEARINGS IN PLACE. ONCE SET SCREWS HAVE BEENV-Belt Tension Adjustment-Tumbler To Idler I. V-Belts refer to illustration in Sections I, J and KV-Belt Tension Alignment - Motor To Idler L. Lintscreen To Replace Lintscreen To Replace V-BeltsJ. Motor To Replace Motor K. ImpellerSECTION Trouble ShootingA. Phase 5 Coin System Diagnostics Diagnostic L.E.D. Display Failure CodesMicroprocessor Controller Relay Output L.E.D. Indicators L.E.D. Display IndicatorsNOTE If the dryer is started the L.E.D. display indicator dots are on and there are no outputs heat and/or motor output L.E.D.s are off and the dOOr input L.E.D. is on, the fault is in the Phase 5 coin microprocessor controller computer itself. If the failure was elsewhere i.e., dryers door switch circuit the L.E.D. display would read dOOr if a keyboard entry was attempted. If the L.E.D. display indicators are on and the door L.E.D. input and motor/heat output L.E.D.s are on and the motor and/or heat is not active ON, then the problem is not the door switch circuit or the Phase 5 coin microprocessor controller the problem is else where in the dryer B. No Heat Condition Page C. No Start Condition D. No Display Condition Page E. dSFL Display Condition F. dOOr Display Condition Technical Information A. Data LabelSECTION B. Using A Manometer C. L.E.D. Display Codes D. Computer Logic and Wiring Diagram including ALL revisions of the number listed below B672611 Diagrams for this book are as followsADC450179 1- 01/08/98-502* 05/21/98-50