AMX none WAV-BP and WAV-BPM Batteries

42 Specifications WAVE 2-Way Wireless Accessories and Adapters for Touch Panels

WAV-BP and WAV-BPM Batteries

Figure 45 shows the WAV-BP and WAV-BPM batteries. Figure 46 shows the specifi-

cations.

WAV

-

BP

WAV

-

BPM

WAV-BP and WAV-BPM specifications

Battery voltage

Type

Amp hour (Ah):

WAV-WP

WAV-BPM

Weight:

WAV-BP

WAV-BPM

Dimensions:

WAV-BP

WAV-BPM

Model number:

WAV-PK

WAV-PKM

12 VDC

Sealed lead acid

2.3 Ah

2.0 Ah

22.8 oz (635 gm)

20.0 oz (590 gm)

2.4" x 7.2" x 0.9" (61 mm x 183 mm x 24 mm)

2,6" x 5.6" x 0.9" (65 mm x 143 mm x 24 mm)

WAV-BP

WAV-BPM

Note

To maximize the recharge life

of the battery, do not com-

pletely discharge the battery,

and recharge the battery im-

mediately after use.

Figure 45

WAV-BP and WAV- BPM bat-

teries

Figure 46

WAV-BP and WAV-BPM

specifications

Contents

Main Limited Warranty and Disclaimer Table of Contents Page Introduction Features Whats in this Manual Whats New AXR-WAVES WAV-PK WAV-PKM WAV-LNK WaveLink WAV-PM WaveLink power module Related Instruction Manuals Sample Product Application (rear panel) AXCESS CardFrame supply WAV-PK Page WAV-PK WAV-PKM WAV-LNK WaveLink Page Optional WAV-PM WaveLink Power Module Page Power management Batteries Safe handling and usage of the battery Standard Power Supply Optional WAV-CHG Fast-Cycle Battery Charger Page Pre-Installation Overview AXR-WAVES (or WAV-LNK) Group Address DIP Switch AXR-WAVES (or WAV-LNK) Group ID DIP Switch WAV-PK Group ID DIP switch WAV-PKM Group ID DIP switch Battery Charging WAV-PM WaveLink Power Module Page Installation Overview Installing the Control System Wiring the AXR-WAVES Guidelines Preparing captive wires Connecting AXlink for data and power Installing the WAV-PK WAV-PK Battery Replacement Replace the WAV-PK battery (Figure 29) as follows. 1. Remove the battery cover by pressing outward on each of the battery cover re- lease tabs while lifting upward and backward at the same time. 2. Grasp the battery and lift it from the battery compartment. Then, pull the bat- Installing the WAV-PKM WAV-PKM Battery Replacement Page Installing the WAV-PM Single WAV-PM module When using a single WAV-PM to power a WAV-LNK, see Figure 34 for connections. Multiple WAV-PM modules Firmware Upgrades Overview AXR-WAVES Server Firmware WAV-PK Battery Pack Firmware Page WAV-PKM Battery Pack Page Page Specifications AXR-WAVES Figure 39 shows the AXR-WAVES. The specifications are in Figure 40. WAV-PK Figure 41 shows the WAV-PK. The specifications are in Figure 42. WAV-PKM Figure 43 shows the WAV-PKM. The specifications are in Figure 44. WAV-BP and WAV-BPM Batteries - WAV-LNK WaveLink Figure 47 shows the WAV-LNK transceiver and Figure 48 shows the specifications. WAV-PM Power Module Figure 49 Shows the WAV-PM Power Module and Figure 50 shows the specifica- tions. Contacting Sales and Technical Support Overview U.S. Sales and Technical Support Teams Panja International Offices Technical Support