Support Module Installation and Wiring

Pull down

FIG. 26 Removing the circuit board

Cut here for access

FIG. 27 For side access, cut out the side vents on the scored lines.

6.Snap the circuit board back into the sub-base by sliding the top of the board in first and then snapping down on the bottom. Check to be sure that the latch holds the board properly.

7.Strip ¼ inch of insulation from the four wires at the support module. Install the wires in the terminals labeled RSR, RSC, RSB and RSA. One twisted pair of wires should be used for the RSR and RSC connection and another pair of twisted wires should be used for the RSB and RSA connection. Push the extra wire back into the wall cavity. Seal the hole in the wall around the cable to eliminate any draft that might affect the sensor.

8.Connect the wires on the thermostat sub-base to the terminals labeled RSR, RSC, RSB and RSA on the ViewStat base (see FIG. 5 on page 10) and the Communication and Equipment Terminal Wiring Definitions table on page 20). Make sure that each terminal on the support module is wired to the terminal with the same label at the thermostat.

9.If necessary, change the Support Module DIP switch settings as described in Setting the Support Module DIP Switches section on page 35.

DIP switches must be set prior to powering the support module (support module is powered when thermostat is returned to its base). If switches need to be changed after powering the support module, the thermostat must be removed from its base for a minimum of 15 seconds to ensure proper reset of the support module.

10.Mount the thermostat on the sub-base and confirm that it is displaying the right temperature from the support module or remote sensor.

Multiple Support Module Installation

Up to 4 support modules can be connected to provide temperature or humidity averaging in a large area or for several zones being controlled by the same system. The maximum cumulative distance of all the support modules from the ViewStat is 1000 ft (304.8 m).

FIG. 28 shows daisy-chaining of the VST-TTM Remote Temperature and VST-TRH Remote Temperature/ Humidity Sensors.

34

ViewStat Communicating Thermostat

Page 39 Page 41
Page 40
Image 40
AMX ViewStat manual Multiple Support Module Installation, Removing the circuit board
Page 39 Page 41

ViewStat specifications

AMX ViewStat is a revolutionary thermostat solution designed for both residential and commercial environments, providing robust control over heating, ventilation, and air conditioning (HVAC) systems. This intelligent device stands out for its user-friendly interface, advanced technology integration, and versatility in various settings.

One of the main features of AMX ViewStat is its intuitive touch screen interface, which enables users to easily navigate through settings and preferences. This 4.3-inch color display not only enhances usability but also allows for customization, offering users the ability to personalize the user experience according to their lifestyle and preferences. Whether adjusting temperature settings or scheduling heating/cooling cycles, the interface ensures a seamless interaction.

Among its key technological advancements is the integration of Wi-Fi connectivity. By connecting to a home or building's network, users can remotely access and control the thermostat through a smartphone, tablet, or computer. This level of control facilitates energy savings, as users can monitor and adjust settings from anywhere, leading to optimized usage and reduced utility bills.

AMX ViewStat is compatible with various HVAC systems, accommodating both conventional and heat pump setups. Its flexibility in adapting to different configurations makes it suitable for diverse applications, from single-family homes to large commercial spaces.

Moreover, the device incorporates advanced energy management features, granting users insights into their energy usage patterns. This data-driven approach allows users to make informed decisions about their energy consumption, ultimately promoting a more sustainable lifestyle.

In addition to its primary functions, AMX ViewStat integrates with other AMX control solutions, enabling a centralized command for home or office automation. When combined with AMX automation systems, users can achieve a fully integrated environment where lighting, security, and entertainment systems work in harmony with heating and cooling controls.

The construction of AMX ViewStat is robust yet stylish, designed to fit seamlessly into any decor. Available in multiple finishes, it adds a touch of elegance while ensuring durability and functionality.

In conclusion, AMX ViewStat is a state-of-the-art thermostat solution that offers a blend of advanced technology, ease of use, and energy efficiency. With features like remote connectivity, compatibility with various HVAC types, and integration with broader automation systems, it stands as a comprehensive solution for modern living and working environments.
Top Page Image Contents