���AMP Device Mode
The ADevice Mode button configures the CR102 to control the AVR600/AV888. Pressing this button does not affect the currently selected input on the AVR600/ AV888.
IMPORTANT: The CR102 must also be in AMP Device
Mode to control the following sources: PHONO, MCH (multichannel analogue), AUX, NET (optional network audio), USB, IPOD (for use with the optional Arcam rLead or rDock).
However to control the internal Tuner in the AVR600 (AM/FM/DAB or Sirius if fitted), the CR102 must first be in Tun Device Mode (see later).
The functionality of the CR102 is context sensitive for the internal sources and is described in the following table.
PSingle press – Toggles AVR600/AV888 power between standby and on in the current zone (zone in which the command is received).
Press and hold – Forces all AVR600/AV888 zones into standby, regardless of which zone the command was received in.
0…9 | The number keys can be used for source |
| selection (without changing the CR102 |
| Device Mode). Alternatively the Device |
| Mode buttons can also be used with the |
| SHIFT key. |
| 0SAT (satellite) input |
| 1PHONO input |
| 2AV input |
| 3TUNER input |
| 4DVD input |
| 5TAPE input |
| 6VCR input |
| 7CD input |
| 8AUX (front panel) input |
| 9MCH (multichannel) input |
PHONO | Selects Tape input on the AVR600/AV888 |
ESHIFT + Eselects Phono input on the AVR600/AV888
RPT | (for iPod and NET sources) |
R
SModifies many keys (see individual key descriptions below).
AUX | Selects MCH (multichannel) input on the |
HAVR600/AV888
SHIFT + Hselects AUX input on the AVR600/AV888
| Navigate menus |
�� | OK confirms a setting (equivalent to ‘Enter’ |
| |
| or ‘Select’ on some remote controls) |
Press and hold OK to force the analogue and digital video outputs to the default resolution: 480i
Shift + <decreases the picture resolution. Shift + >increases the picture resolution. Shift + 'turns current zone (in which command is received) on
Shift + ,turns current zone (in which command is received) off.
NET | Selects iPOD input on the AVR600/AV888 |
ESHIFT + E selects network (net) internal input on the AVR600/AV888
MCycles through the available surround and downmix modes.
UDisplays the AVR600/AV888 setup menu on the On Screen Display (see page 34).
DCycles through the front panel display’s brightness options
@TogglesAV888 the mute function of the AVR600/
] [ (track control for iPod and NET sources) | |
| SHIFT + [Follow Zone1 source. |
| When the command is received in Zone2 |
| or Zone3, the source for that zone follows |
| whatever input source is selected in Zone1 |
- + | Decrease |
| AV888 volume |
DIRECT | Stereo direct on/off. Provides a direct |
) | analogue path from the analogue inputs to |
| the left and right front outputs. Switches off |
| any surround processing modes and shuts |
| down the DSP circuits for the best stereo |
| sound quality. |
EQ | Displays the room EQ settings menu |
$ |
|
EFFECT | (for iPod and NET sources) |
& |
|
BASS | Calls up a |
( | adjust the bass setting for a particular input. |
Trim | Brings up the speaker trim menu. |
!Use the B, C, D and E navigation buttons. Press TRIM again to exit the speaker trim menu.
As this is a temporary adjustment, these additional trim levels are reset to zero when the unit is turned off or the selected input is changed, but are retained if the unit is put into standby. These temporary trim levels are independent of the speaker levels found in the setup menu.
sync | Delays may be introduced into the video |
#signal by video processing which causes a mismatch between the audio and video timing. You will notice this by speech sound being out of synchronization with the lip movements in the video.
To compensate for this, you can adjust the lip sync delay. Press the sync button and use the D and E navigation buttons. Press again to exit the lip sync trim menu.
SUB | Brings up the subwoofer trim menu. Use |
%the D and E navigation buttons. Press Sub again to exit the sub trim menu
TREBLE | Calls up a |
Hadjust the treble setting for a particular input.
FAV+ | (for iPod and NET sources) |
U |
|
FAV- | (for iPod and NET sources) |
T |
|
HOME | (for iPod and NET sources) |
O |
|
INFO | Cycles through the information displayed |
Bon the lower left portion of the front panel display.
iPod commands
The iPod interface is selected by pressing E in AMP Device Mode on the CR102. When connected to an iPod via an optional rLead/rDock, the keys below are used to navigate music files in AMP Device Mode.
| Navigate the files on screen. |
�� | OK selects/play the highlighted file. |
RPT | Toggles random (shuffle) play of the playlist |
Ron and off.
SHIFT + Rcycles through the repeat options
] [ | Selects the previous/next track in the |
| current playlist |
$ | Begins or resumes playback at the currently |
| highlighted track |
&Togglestrack pause and playback of the current
#Stops playback