Operating your P7

P7 MULTICHANNEL POWER AMPLIFIER

1

2

3

4

5

6

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FRONT PANEL LAYOUT

OPERATING PROCEDURE

The P7 front panel has a single control: a centrally located power on/off button.

POWER

Switches the unit on and off. Note that the modules are turned on individually to stagger the surge created when a powerful amplifier is switched on (i.e., it provides a ‘soft start’). This reduces the surge current drawn from the domestic power supply.

STATUS LEDS

A separate LED indicates the status of each of the seven channels of the P7.

The LEDs cycle through red, orange, then green to indicate the status from powered-up (initialised), stabilised and active respectively.

All LEDs are off in standby mode.

Once the relevant connections have been made, the P7 can be switched on using the central button on the front panel.

SWITCHING ON

It is recommended that you switch on your pre-amp or controller before powering up the P7 power amp.

Normal powering up is indicated by the following sequence of front panel LED indicators:

1.On pressing the power switch, all LEDs turn red.

2.After approximately half-a-second, the centre LED turns amber.

3.The LEDs continue turning amber from the centre to the edges in pairs, with intervals of approximately one second.

4.The centre LED turns green and a relay ‘click’ is heard.

5.The LEDs continue turning green from the centre to the edges in pairs, along with relay ‘clicks’, with intervals of approximately one second.

If the LEDs do not follow this sequence when the P7 is powered up, or behave abnormally at any time during use, then consult the table of ‘Fault status indicators’ on page 11 to discover why the amplifier is in protection mode.

SWITCHING OFF

To shut down, switch the P7 power amp off first, followed by the pre- amp or controller.

This eliminates the chance of any ‘thumps’ or power spikes being fed through to the power amplifier and potentially causing damage to the system.

NOTE: It is recommended that if the unit is switched off, then it should not be switched on again for at least 20 seconds from when it was turned off.This allows the amplifier’s power supply to discharge fully before it is switched on again.

8

Page 7 Page 9
Page 8
Image 8
Arcam Multichannel Power Amplifier manual Operating your P7, Front Panel Layout
Page 7 Page 9

Multichannel Power Amplifier specifications

The Arcam Multichannel Power Amplifier stands out in the audio landscape, delivering exceptional performance and versatility for home theater and multi-room audio systems. Known for its hallmark sound quality, this amplifier is designed to elevate the listening experience, leveraging advanced technologies and premium components.

One of the primary features of the Arcam Multichannel Power Amplifier is its high power output, which allows it to drive even the most demanding speakers with ease. With multiple channels typically offering 100-200 watts per channel, the amplifier is capable of providing clear, dynamic sound across all frequencies. This high output ensures that users can enjoy a powerful cinematic experience without distortion, making it ideal for both music and movie playback.

Another key characteristic of the Arcam amplifier is its Class G amplification technology. Unlike traditional Class A or Class AB designs, Class G dynamically adjusts power supply voltages based on the signal level. This results in improved efficiency and lower heat generation while maintaining optimal audio fidelity. As a result, users benefit from enhanced performance during extended listening sessions without the risk of overheating.

The amplifier also incorporates advanced signal processing features, including high-quality DACs (Digital to Analog Converters) and extensive connectivity options. It supports various audio formats and protocols, allowing users to integrate it seamlessly into existing systems, whether utilizing HDMI, analog, or digital connections. This flexibility makes it compatible with a wide range of audio sources, from Blu-ray players to gaming consoles and streaming devices.

Moreover, the Arcam Multichannel Power Amplifier features robust build quality with premium components designed for longevity and reliability. The use of high-grade capacitors, heatsinks, and sturdy chassis construction ensures that the amplifier can withstand rigorous use in diverse environments.

In terms of usability, it often includes features like trigger inputs, remote control operation, and automated standby modes for convenience. User-friendly interfaces and capabilities allow users to customize their listening experience, enhancing their engagement with the audio content.

In summary, the Arcam Multichannel Power Amplifier represents a pinnacle of audio engineering, combining powerful performance, innovative technologies, and user-friendly features. It is an ideal choice for audiophiles and home theater enthusiasts seeking an amplifier that delivers rich, immersive sound quality across multiple channels, while maintaining efficiency and reliability.
Top Page Image Contents