IMPORTANT: DO NOT use gasohol or gasoline containing alcohol. See Engine Manual for correct type and grade of fuel.

5.Fill fuel tank to within 1/2 in. (1.2 cm) below bottom of filler neck with unleaded gasoline.

NOTE: Tank capacity is 1 gallon (3.8 liters).

6.Replace Fuel Cap and tighten.

7.ALWAYS clean up any spilled fuel.

PRE-START1. Frozen Impeller

IMPORTANT: Before starting engine, check impeller to be sure it is not frozen.

To check impeller:

1.With ignition key switch in “Stop” position, squeeze Attachment Clutch Lever to Engaged position.

2.Pull Recoil Starter Handle.

3.If Impeller is frozen, (cannot pull Starter Handle) move unit to a heated area and thaw to prevent possible damage.

2.Check Function of Clutches

If clutches do not engage or disengage properly, adjust or repair before operation (see SERVICE AND ADJUSTMENTS on page 22).

3. Check Dual Handle Interlock

Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Attachment clutch should remain engaged until traction clutch lever is released, then both clutches must disengage.

If clutches do not engage or disengage properly, adjust or repair before operation (see SERVICE AND ADJUSTMENTS on page 22).

4.Check Remote Differential (926004, 005, 006, 300, 301, 500, 501)

Test the remote differential lock before starting. Squeeze and hold the remote differential lever to lock differential so both wheels drive and provide better traction. Release the remote differential lever to allow easier steering.

If remote differential does not engage or disengage properly, adjust or repair before operation (see REMOTE DIFFERENTIAL (926004, 005, 006, 300, 301, 500, 501) on page 23).

5.Check Remote Wheel Lock (926002, 003, 102, 103, 302, 303, 304)

Squeeze and release the remote wheel lock to lock the left wheel for better traction when throwing snow or to unlock the left wheel for easier steering.

If remote wheel lock does not lock or unlock properly, adjust or repair before operation (see REMOTE WHEEL LOCK (926002, 003, 102, 103, 302, 303, 304) on page 23).

6.Check Adjust Axle Lock (926001, 101, 504, 505)

Use the axle lock pins to lock or unlock the wheels. Lock both wheels to increase traction; unlock one wheel to allow for easier turning of the unit.

7. Check Runners

Check and adjust Runners (SERVICE AND ADJUSTMENTS on page 22). Allow 1/8 in. (3 mm) between scraper blade and hard, smooth surface(s). Allow 1-1/4 in. (30 mm) between scraper blade and uneven or gravel surfaces.

8. Check Engine Fuel & Crankcase Oil

WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding.

Check and add fuel if required. Check that the engine crankcase oil is full using dipstick. Refer to Engine Manual for detailed instructions.

TO STOP IN AN EMERGENCY

Immediately release both control levers to stop unit in an emergency. Stop engine, remove key and wait for all rotating parts to stop before leaving operator’s position.

STARTING AND SHUT OFF

WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. DO NOT attempt to start your unit at this time. Read entire Owner/Operator Manual and the Engine Manual first.

IMPORTANT: Allow unit and engine to adjust to the outdoor temperature before clearing snow. Before shut-off, run the attachment a few minutes to prevent impeller freeze-up.

NOTE: Try out each control without the engine running to see how it works and what it does.

Manual Start

1.Turn discharge chute straight ahead.

2.Make sure that the traction clutch and attachment drive clutch levers are fully disengaged.

3.Push Primer Bulb 2 or 3 times for cold engine.

NOTE: When temperature is below -15° F (-26° C) additional priming may be needed.

4.If engine is cold, apply choke. See Engine Manual for detailed instructions.

GB - 17