MAINTENANCE SCHEDULE
The chart below shows the recommended maintenance schedule that should be performed on a regular basis. More frequent service may be required.
MAINTENANCE SCHEDULE
Service Performed | Each Use | Every 5 | Every 25 | Yearly |
|
| hrs. | hrs. |
|
|
|
|
|
|
Check Dual Handle | • |
|
|
|
Interlock |
|
|
|
|
|
|
|
|
|
Check Fasteners | • |
|
|
|
|
|
|
|
|
Check Clutch | • |
|
|
|
Operation |
|
|
|
|
|
|
|
|
|
Check Clutch Spring |
| * | • |
|
Adjustments |
|
|
| |
|
|
|
| |
|
|
|
|
|
Clean Engine | • |
|
|
|
|
|
|
|
|
Check Engine Oil |
| • |
|
|
|
|
|
|
|
Change Engine Oil |
| ** | • |
|
|
|
|
| |
|
|
|
|
|
Check Tire Pressure |
|
| • |
|
|
|
|
|
|
Check Auger |
|
| • | • |
Gearcase |
|
|
|
|
|
|
|
|
|
General Lubrication |
|
| • | • |
|
|
|
|
|
Battery Maintenance |
|
| • | • |
|
|
|
|
|
*After first five hours of operation.
**After first two hours of operation.
CHECK DUAL HANDLE INTERLOCK
Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Attachment clutch should remain engaged until traction clutch lever is released, then both clutches must disengage.
CHECK FASTENERS
Make sure all hardware is tightened properly.
CHECK CLUTCH OPERATION
Auger / impeller must stop within 5 seconds when attachment clutch/impeller brake lever is released.
Wheels must stop quickly when traction drive clutch lever is released.
If clutches do not engage or disengage properly, adjust or repair before operation (see SERVICE AND ADJUSTMENTS on page 22).
CHECK CLUTCH SPRING ADJUSTMENT
Make sure the attachment clutch and traction drive clutch are adjusted to the range specified in Attachment Clutch/Brake Adjustment on page 25.
CLEAN ENGINE
Refer to Engine Manual for detailed instructions.
CHECK ENGINE OIL
The engine crankcase oil should be checked every 5 hours of operation. Oil level MUST be maintained in safe operating range on dipstick at all times or engine damage will result (See Engine Manual).
Park unit on a level surface. Refer to Engine Manual for detailed instructions.
CHANGE ENGINE OIL
Change oil after first 2 hours of operation, thereafter change oil every 25 hours (more often if required). Refer to Engine Manual for detailed instructions.
Run engine just prior to changing oil. Warm oil will flow more freely and carry away more contamination. Remove the oil drain plug from the rear of the unit and tip the unit back to help drain all the oil.
CHECK TIRE PRESSURE
Keep tires at pressure listed on the tire sidewall.
CHECK AUGER GEARCASE
IMPORTANT: Proper oil level must be maintained.
Gear cases are filled to the correct level at the factory. Unless there is evidence of leakage, no additional lubricant should be required. Check oil level each season or every 25 hours of operation.
To ensure adequate lubricant level:
1.Remove filler plug (Figure 17). Lubricant must be at least up to bottom of lubricant filler hole with unit resting on a
2.Add lubricant if required. Allow oil to drain to level of plug and replace plug.
IMPORTANT: Use only Ariens special gear lubricant
1
3
2
1.Auger Gearcase - Cast Iron
2.Oil Fill and Drain Plug
3.Auger Gearcase - Aluminum
Figure 17 | OS7130 |
|
GB - 20