Manuals / ATEN Technology / Computer Equipment / Network Card

ATEN Technology ACS-1208AL Removing the Keyboard and Touchpad, Remove the two attaching screws

Models: ACS-1208AL ACS-1216AL

1 73

Download 73 pages 23.35 Kb

Page 65

Removing the Keyboard and Touchpad

KL0116 User Manual

Removing the Keyboard and Touchpad

The keyboard and touchpad can be easily removed for repair or replace- ment:

1. Remove the two attaching screws.

B-2

2003-01-27

Image 65

ATEN Technology ACS-1208AL, ACS-1216AL user manual Removing the Keyboard and Touchpad, Remove the two attaching screws

Contents

User Manual ACS-1208AL ACS-1216ALFor additional information This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Packing List Installation Table of Contents1. Introduction Hotkey OperationAppendix A, Technical Information 5. The Firmware Upgrade UtilityAppendix B, Module Removal Appendix C, Rack MountingOverview About This ManualM Bullet lists provide information, but not procedural steps 2003-01-27 ACS-1208AL / ACS-1216AL User Manualviii Chapter IntroductionOverview a 1U system rack. Because of its modular design, the KVM section can be detached from the switch section. If you ever need to expand your connections, you can remove the 8 port Switch module and replace it with a 16 port Switch module Features Hardware Requirements 2L-1700 / 2L-1701 2L-5201P / 5202P / 5203P 1. Handle ACS-1208AL / ACS1216AL Front View2. Cover 3. Port LEDs10. Reset Switch 4. Keyboard 5. Power LED6. Slide Release 7. Rack Mounting BracketsACS-1208AL / ACS-1216AL Rear View 4. Power Jack1. Daisy Chain Port 2. CPU Port Section6. Firmware Upgrade Recovery Switch 5. Firmware Upgrade PortLCD OSD Configuration Single Stage Installation InstallationBefore you Begin ChapterDaisy Chaining To set up a daisy chained installation, do the following ACS-1216AL ACS-1216A ACS-1216A ACS-1208AL / ACS-1216AL User Manual2003-01-27 Hot Plugging CPU Ports Switching Station PositionsHot Plugging Port ID Numbering Port Selection Powering Off and Restarting2003-01-27 ACS-1208AL / ACS-1216AL User ManualHotkey Operation Hotkey Port AccessInvoking Hotkey Mode Chapter3. Press Enter Selecting the Active Port3. Press Enter Setting the Scan IntervalAuto Scan Paused Invoking Auto Scan1. Invoke Hotkey Mode see p 2. Key in Arrow Summary ControlHotkey Chapter OSD OperationOSD Operation When you invoke the OSD, a screen similar to the one below appears OSD Main Screen Headings OSD NavigationHeading ExplanationF1 GOTO OSD FunctionsMeaning F2 LISTChoice F3 SET ACCESSIBLE PORTS, p SettingQUICK VIEW + POWERED ON - Only those Ports which Functionpassword appears. The username and password may be up F4 ADM3. For each individual, key in the Username and Password, then to 15 characters long, and can consist of any combination ofDEFAULT SETTINGS, p. A-2 - except for the Names settings SettingF4 ADM continued Table continues on next pageThis function allows the Administrator to define User access to SettingView Only, or blank. Repeat until all access rights have been FunctionPort Names, all Administrator settings such as Set Accessible SettingF4 ADM continued FunctionF5 SKP F6 BRC F7 SCAN F8 LOUT 2003-01-27 ACS-1208AL / ACS-1216AL User Manual4-16 Chapter The Firmware Upgrade UtilityIntroduction Begin Upgrade Performing the Upgrade3. Click Next to continue. The Firmware Upgrade Utility main screen appears 5. After you have made your selections, Click Next to perform the upgrade Upgrade Upgrade FailedSucceeded Firmware Upgrade Recovery 2003-01-27 ACS-1208AL / ACS-1216AL User ManualACS-1208AL / ACS-1216AL - Connection Tables Technical InformationAppendix A ACS-1208ALACS-1216AL OSD Factory Default SettingsSetting DefaultFunction SpecificationsACS-1208AL ACS-1216ALClear Login Information Limited Warranty TroubleshootingSymptom Possible Cause2003-01-27 ACS-1208AL / ACS-1216AL User ManualAppendix B Module RemovalRemoving the KVM Module 1. Remove the two attaching screws Removing the Keyboard and Touchpad4. Lift the module clear and unplug the cables 2003-01-27 KL0116 User ManualAppendix C Rack MountingStandard Rack Mounting Optional Rack Mounting 4. Screw the metal tabs to the rear flanges 3. Slide the unit into the rack5. Secure the unit to the rack with the front flanges and rear tabs Rack Mounting2003-01-27 KL0116 User ManualG - H IndexE - F Q - R