Atlantis Land A02-RA144-W300N 45

WebShare 144WN

establish membership in a Multicast group - it is not used to carry user data. IGMP version 2 (RFC 2236) is an improvement over version 1 (RFC 1112) but IGMP version 1 is still in wide use. If you would like to read more detailed information about interoperability between IGMP version 2 and version 1, please see sections 4 and 5 of RFC 2236. The class D IP address is used to identify host groups and can be in the range 224.0.0.0 to 239.255.255.255. The address

224.0.0.0is not assigned to any group and is used by IP multicast computers. The address 224.0.0.1 is used for query messages and is assigned to the permanent group of all IP hosts (including gateways). All hosts must join the

224.0.0.1group in order to participate in IGMP. The address 224.0.0.2 is assigned to the multicast routers group.

The ADSL Router supports both IGMP version 1 (IGMP-v1) and IGMP version 2 (IGMP-v2). At start up, the ADSL Router queries all directly connected networks to gather group membership. After that, the ADSL Router periodically updates this information. IP multicasting can be enabled/disabled on the ADSL Router LAN and/or WAN interfaces in the web configurator (LAN; WAN). Select None to disable IP multicasting on these interfaces.

A02-RA144-W300N

Pag. 35

Contents

A02-RA144-W300N Page CHAPTER 1: INTRODUCTION CHAPTER 2: USING WEBSHARE WIRELESS ADSL2+ ROUTER CHAPTER 3: CONFIGURATION CHAPTER 4: QUICK START CHAPTER 5: LAN SETUP CHAPTER 8: ACCESS MANAGEMENT CHAPTER 9: ADVANCED SETUP CHAPTER 10: MAINTENANCE CHAPTER 11: STATUS APPENDIX A: TROUBLESHOOTING APPENDIX B: TECHNICAL FEATURES APPENDIX C:SUPPORT Page Copyright Statement Wireless LAN, Health and Authorization for use Regulatory Information/disclaimers CE Mark Warning CE in which Countries where the product may be used freely: CE/EMC Restriction of Liability Declaration of Conformity France: Page CHAPTER 1: Introduction 1.1 An Overview of WebShare Wireless N ADSL2+ Router 1.2 Package Contents 1.3 WebShare Wireless N Router ADSL2+ Features RIP1/2 Routing Web based GUI Quick Installation Wizard: Packet Filtering: Up to 72 rules Virtual Server: 1.4 WebShare Wireless N Router ADSL2+ Application Page CHAPTER 2: Using WebShare Wireless N ADSL2+ Router 2.1Cautions for using the WebShare Wireless N ADSL2+ Router 2.2 The Front LEDs 2.3 The Rear Ports 2.4 Cabling Page CHAPTER 3: Configuration 3.1 Before Configuration 3.1.1 Configuring PC for Windows 95/98/ME Page 3.1.2 Configuring PC for Windows NT4.0 3.1.3 Configuring PC for Windows Page 3.1.4 Configuring PC for Windows XP Page 3.1.5 Configuring PC for Windows Vista 3.1.6 Configuring for MAC 3.1.6 Verification of Configuration 3.1.7 Browser Configuration 3.2 Factory Default Setting 3.2.1 Password 3.2.2 LAN and WAN Port Addresses 3.3 Reset of WebShare Wireless N ADSL2+ Router 3.4 Informations from the ISP 3.5 Browser Configuration 3.6 Surfing in Web GUI Configuration 3.7 Configuring Password 3.8 Resetting the ADSL Router 3.8.1 Using The Reset Button CHAPTER 4: Quick Start 4.1 Wizard Setup Introduction 4.2 Encapsulation 4.2.1 PPP over Ethernet 4.2.2 PPPoA 4.3 Multiplexing 4.3.1 VC-basedMultiplexing 4.3.2 LLC-basedMultiplexing 4.4 VPI and VCI 4.5 Quick Start PPPoE/PPPoA: Static IP address: PPPoE/PPPoA Username Password In case of PPPoE choose Connection Type=PPPoE LLC STATIC IP ADDRESS RFC1483 4.6 Wizard Setup Configuration: Connection Tests CHAPTER 5: LAN Setup 5.1 LAN Overview 5.1.1 LANs, WANs and the ADSL Router 5.2 DNS Server Address 5.3 DNS Server Address Assignment 5.4 LAN TCP/IP 5.4.1 Factory LAN Defaults 5.4.2 IP Address and Subnet Mask 5.4.3 RIP Setup 5.4.4 Multicast Page 5.5 Configuring LAN DHCP Enabled Disabled Relay Starting IP 5.6 Wireless RTS/CTS Threshold Fragmentation DTIM Wireless Mode WMM Enable Yes WPS Settings WPS State WEP-64bitsor WEP-128bits WPA-PSK Authentication Type TKIP Pre-Shared Wireless MAC Address Filter Activated/Deactivated Actived Action Deny Association 6.1 WAN Overview 6.2 PPPoE Encapsulation 6.3 PPTP Encapsulation 6.4 Traffic Shaping Page 6.5 Configuring WAN Setup PARAMETRES DESCRIPTION ATM VC Virtual Circuit ID VPI Default Route IP Address Get IP Address IP Address Gateway NAT Connect on Demand IGMP-v2 7.1 NAT Overview 7.1.1 NAT Definitions 7.1.2 What NAT Does 7.1.3 How NAT Works 7.1.4 NAT Application 7.1.5 NAT Mapping Types 7.2 SUA (Single User Account) Versus NAT 7.3 Virtual Server and DMZ 7.3.1 Port Forwarding: Services and Port Numbers 7.3.2 Virtual Server Page Start Port No End Port No IP Address 7.4 Selecting the NAT Mode Rule Index Rule Type Local Start IP Local End IP Public Start IP CHAPTER 8: Access Management 8.1 ACL 8.2 IP Filter IP FILTER RULE EDITING: Ip Filter Index Active Source 8.3 SNMP 8.4 UPnP 8.5 DDNS Dynamic DNS Service Provider My Host Name E-MailAddress Wildcard CHAPTER 9: Advanced Setup 9.1 Routing 9.1.1 Add Route 9.2 NAT 9.2.2 DMZ 9.2.3 Virtual Server 9.2.4 IP Address Mapping 9.3 QoS Rule Physical Ports Destination MAC IP (Destination) (Destination) Remarking: Type of Service DSCP Remarking 802.1p Remarking Queue 9.4 ADSL CHAPTER 10: Maintenance 10.1 Administration 10.2 Time Zone 10.3 Firmware New Firmware Location Browse Browse 10.4 SysRestart 10.5 Diagnostic Page CHAPTER 11: Status 11.1 Device Info 11.2 System Log 11.3 Statistics ETHERNET: Transmit Frames Transmit Multicast Frames Transmit total Bytes Transmit Collision Page APPENDIX A: Troubleshooting A.1 Using LEDs to Diagnose Problems A.1.1 Power LED A.1.2 LAN LED A.1.3 DSL LED A.2 Telnet A.3 Web Configurator A.4 Login Username and Password A.5 LAN Interface A.6 WAN Interface A.7 Internet Access A.8 Remote Management A.9 Remote Node Connection A.10 FAQ Page Page APPENDIX B: Technical Features Page APPENDIX C:Support