Manuals / Brands / Computer Equipment / Network Router / Atlantis Land / Computer Equipment / Network Router

Atlantis Land A02-RA144-W300N 10.4 SysRestart, 10.5 Diagnostic, SysRestart, Current Settings, Factory Default Settings

1 103

Download 103 pages, 1.3 Mb

WebShare 144WN

10.4 SysRestart

Click SysRestart with option Current Settings to reboot your router (and restore your last saved configuration).

If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default settings.

You may also reset your router to factory settings by holding the small Reset pinhole button on the back of your router in for 10-12 seconds whilst the router is turned on.

10.5 Diagnostic

The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides.

A02-RA144-W300N

Pag. 77

Contents

A02-RA144-W300N Page CHAPTER 1: INTRODUCTION CHAPTER 2: USING WEBSHARE WIRELESS ADSL2+ ROUTER CHAPTER 3: CONFIGURATION CHAPTER 4: QUICK START CHAPTER 5: LAN SETUP CHAPTER 8: ACCESS MANAGEMENT CHAPTER 9: ADVANCED SETUP CHAPTER 10: MAINTENANCE CHAPTER 11: STATUS APPENDIX A: TROUBLESHOOTING APPENDIX B: TECHNICAL FEATURES APPENDIX C:SUPPORT Page Copyright Statement Wireless LAN, Health and Authorization for use Regulatory Information/disclaimers CE Mark Warning CE in which Countries where the product may be used freely: CE/EMC Restriction of Liability Declaration of Conformity France: Page CHAPTER 1: Introduction 1.1 An Overview of WebShare Wireless N ADSL2+ Router 1.2 Package Contents 1.3 WebShare Wireless N Router ADSL2+ Features RIP1/2 Routing Web based GUI Quick Installation Wizard: Packet Filtering: Up to 72 rules Virtual Server: 1.4 WebShare Wireless N Router ADSL2+ Application Page CHAPTER 2: Using WebShare Wireless N ADSL2+ Router 2.1Cautions for using the WebShare Wireless N ADSL2+ Router 2.2 The Front LEDs 2.3 The Rear Ports 2.4 Cabling Page CHAPTER 3: Configuration 3.1 Before Configuration 3.1.1 Configuring PC for Windows 95/98/ME Page 3.1.2 Configuring PC for Windows NT4.0 3.1.3 Configuring PC for Windows Page 3.1.4 Configuring PC for Windows XP Page 3.1.5 Configuring PC for Windows Vista 3.1.6 Configuring for MAC 3.1.6 Verification of Configuration 3.1.7 Browser Configuration 3.2 Factory Default Setting 3.2.1 Password 3.2.2 LAN and WAN Port Addresses 3.3 Reset of WebShare Wireless N ADSL2+ Router 3.4 Informations from the ISP 3.5 Browser Configuration 3.6 Surfing in Web GUI Configuration 3.7 Configuring Password 3.8 Resetting the ADSL Router 3.8.1 Using The Reset Button CHAPTER 4: Quick Start 4.1 Wizard Setup Introduction 4.2 Encapsulation 4.2.1 PPP over Ethernet 4.2.2 PPPoA 4.3 Multiplexing 4.3.1 VC-basedMultiplexing 4.3.2 LLC-basedMultiplexing 4.4 VPI and VCI 4.5 Quick Start PPPoE/PPPoA: Static IP address: PPPoE/PPPoA Username Password In case of PPPoE choose Connection Type=PPPoE LLC STATIC IP ADDRESS RFC1483 4.6 Wizard Setup Configuration: Connection Tests CHAPTER 5: LAN Setup 5.1 LAN Overview 5.1.1 LANs, WANs and the ADSL Router 5.2 DNS Server Address 5.3 DNS Server Address Assignment 5.4 LAN TCP/IP 5.4.1 Factory LAN Defaults 5.4.2 IP Address and Subnet Mask 5.4.3 RIP Setup 5.4.4 Multicast Page 5.5 Configuring LAN DHCP Enabled Disabled Relay Starting IP 5.6 Wireless RTS/CTS Threshold Fragmentation DTIM Wireless Mode WMM Enable Yes WPS Settings WPS State WEP-64bitsor WEP-128bits WPA-PSK Authentication Type TKIP Pre-Shared Wireless MAC Address Filter Activated/Deactivated Actived Action Deny Association 6.1 WAN Overview 6.2 PPPoE Encapsulation 6.3 PPTP Encapsulation 6.4 Traffic Shaping Page 6.5 Configuring WAN Setup PARAMETRES DESCRIPTION ATM VC Virtual Circuit ID VPI Default Route IP Address Get IP Address IP Address Gateway NAT Connect on Demand IGMP-v2 7.1 NAT Overview 7.1.1 NAT Definitions 7.1.2 What NAT Does 7.1.3 How NAT Works 7.1.4 NAT Application 7.1.5 NAT Mapping Types 7.2 SUA (Single User Account) Versus NAT 7.3 Virtual Server and DMZ 7.3.1 Port Forwarding: Services and Port Numbers 7.3.2 Virtual Server Page Start Port No End Port No IP Address 7.4 Selecting the NAT Mode Rule Index Rule Type Local Start IP Local End IP Public Start IP CHAPTER 8: Access Management 8.1 ACL 8.2 IP Filter IP FILTER RULE EDITING: Ip Filter Index Active Source 8.3 SNMP 8.4 UPnP 8.5 DDNS Dynamic DNS Service Provider My Host Name E-MailAddress Wildcard CHAPTER 9: Advanced Setup 9.1 Routing 9.1.1 Add Route 9.2 NAT 9.2.2 DMZ 9.2.3 Virtual Server 9.2.4 IP Address Mapping 9.3 QoS Rule Physical Ports Destination MAC IP (Destination) (Destination) Remarking: Type of Service DSCP Remarking 802.1p Remarking Queue 9.4 ADSL CHAPTER 10: Maintenance 10.1 Administration 10.2 Time Zone 10.3 Firmware New Firmware Location Browse Browse 10.4 SysRestart 10.5 Diagnostic Page CHAPTER 11: Status 11.1 Device Info 11.2 System Log 11.3 Statistics ETHERNET: Transmit Frames Transmit Multicast Frames Transmit total Bytes Transmit Collision Page APPENDIX A: Troubleshooting A.1 Using LEDs to Diagnose Problems A.1.1 Power LED A.1.2 LAN LED A.1.3 DSL LED A.2 Telnet A.3 Web Configurator A.4 Login Username and Password A.5 LAN Interface A.6 WAN Interface A.7 Internet Access A.8 Remote Management A.9 Remote Node Connection A.10 FAQ Page Page APPENDIX B: Technical Features Page APPENDIX C:Support