Manuals / Brands / Computer Equipment / Network Router / Atlantis Land / Computer Equipment / Network Router

Atlantis Land Mistral Lan Router ISDN show ip , show ip <interface name> , show ip routing table

1 48

Download 48 pages, 318.6 Kb

show ip

Description: This command displays all interfaces on which IP routing has been enabled.

Example:

Router> show ip

Admin. Oper. Destination/

IfName State State IP Address Netmask Broadcast Addr

-------------------------------------------------------------------

ppp2 Enabled Up 20.0.0.1 255.0.0.0 20.0.0.2

lan Enabled Up 110.0.0.1 255.0.0.0 110.255.255.255

dlci16 Enabled Up 10.0.0.1 255.0.0.0 10.0.0.2

dlci17 Enabled Up (Unnumbered)

show ip <interface name>

Description: This command displays the IP configuration over the specified interface.

Example:

Router> show ip lan

Interface: lan

----------------------------------------------------------------

IP Address: 192.168.168.230

Netmask: 255.255.255.0

Dest. IP Address: 192.168.168.255

Opr./Admin. State: Up

RIP State: Active Ver.1

IP Multicast: Disabled

show ip routing table

Description: This command displays the IP routing table. Each entry in the routing table corresponds

to a network or a host, and contains necessary information that is required for routing data packets to

that network or host. For example, entry 8 means that to send a packet to 110.0.0.1, the packet should

be sent to the next hop router (gateway), whose IP address is 40.0.0.5. The destination is, according to

the table, 5 hops away (where a “hop” is a traversal of a link from one router to another).

Any entry whose Interface Name is lo means the corresponding destination network is locally attached

to one of the serial interfaces. Also, if the Gateway field is empty, it means either the destination IP

network is directly attached to the router (i.e., the destination is on the same LAN the router is

connected to), or the destination is reachable through an unnumbered serial interface.

The meanings of the flags are:

Host

S Static Route

G Gateway

C Cloned Entry

Contents

Main Mistral Lan Router ISDN with 4 Fast Ethernet ports + Broadband Interface Page Console Commands General Guidelines Express Mode vs. Advanced Mode Conventions Command Categories From a functional point of view, commands can be grouped into the following functional categories: Router> command (with parameters) Output Command List Bridging Commands Compression Commands DHCP Commands Diagnostic Commands Dial-in User Commands Filtering Commands IP Commands Port Commands Profile Commands Security Command SNMP Commands Statistics Commands System Commands Page Page show learning show learning <Interface Name> Compression Commands clear compression statistics <Profile Name> disable compression <Profile Name> enable compression <Profile Name> show compression statistics <Profile Name> DHCP Commands add dhcp entry <entry name> add dns <primary/secondary> <IP_addr> delete dhcp entry <entry name> delete dns <primary/secondary> disable dhcp enable dhcp set dhcp set range show dhcp show dhcp table show range Page test isdn <dial name> <64k/56k> Dial-in User Commands add user <profile name> (where profile name is a string <= 30 chars) Add the following Single Workstation dialing into the router using the CLI Advanced Mode delete user <profile name> Description: Deletes a dial-in user entry from the local user database. show user [profile name] Example 2: When a specific user is named, the output appears as follows: Filtering Commands add filter <1-8> delete filter <1-8> set filter default show filter show filter <1-8 > add pat entry <public port #> add pat entry default Page ping <ipAddr> [n_times] [n_size] set ip default route <gateway-ipAddr> set ip default route <Profile Name> set ip lan <ip_addr> <netMask> set ip private <ip_addr> <netMask> set ip rip [Interface Name] <disabled/passive/active> <rip1/rip2> set ip <Profile Name> set ip <Profile Name> < local-ipAddr> <netMask> <remote-ipAddr> 255.255.255.0. show arp table show icmp statistics show ip show ip <interface name> show ip routing table Host S Static Route G Gateway C Cloned Entry Example: show ip statistics Description: This csommand displays IP routing related statistics. Example: show pat show tcp statistics show udp statistics Port Commands clear port statistics [port name] disable port <port name> enable port <port name> set port <port name> show port show port <port name> Description: This command displays the configuration of a WAN interface port. Example 1: Example 2: show port statistics <port name> Example 1: Profile Commands add profile <Profile Name> clear profile statistics [Profile Name] connect profile <Profile Name> delete profile <Profile Name> disable profile <Profile Name> disconnect profile < Profile Name> enable profile <Profile Name> show profile show profile <Profile Name> Page disable trap enable trap set community string read <"password"> set trap manager <1-5> <ipAddr> show snmp statistics Page Page Page logout reset system save config set console baud <baudrate> set console timeout <1-60> set date <mm-dd-yy> set daylight time <on/off> set internet access time set log level <1-10> set prompt <prompt> set system contact <name> set system location <location information> set system name <system name> set time <hh:mm:ss> set timezone <-12 - +12> show config show connection log show interface list show internet access time show system show system log