Atlantis Land Mistral Lan Router ISDN - page 38

show profile statistics

Example:

Router> show profile statistics

Prof Oper. Packets Packets Errors Errors Q-full

Name State Sent Rcv'ed Sent Rcv'ed Discard

-----------------------------------------------------------------

wilson Down 0 0 0 0 0

show profile statistics <Profile Name>

Example:

Router> show profile statistics wilson

wilson Received Transmitted

---------------------------------------------------------------

Total octets: 0 0

Total packets: 0 0

Total errors: 0 0

Security Command

set ip private <ip_addr> <netMask>

Description: This command is used to modify the “private” IP address on the router’s LAN interface.

Please refer to IP command category for details.

SNMP Commands

Remote SNMP management consoles can access the set of MIBs implemented in the router. MIB

information is transferred from the router’s SNMP Agent to the SNMP Management console via

SNMP Gets and Traps (Set commands are not supported).. Traps are unsolicited status messages sent

from the router to report management events asynchronously. Trap Managers must be configured in

order to receive these messages.

clear trap manager <1-5>

Description: This command clears the IP address for the specified trap manager. When an SNMP trap

condition is met, and if trap generation has been enabled, a trap message will automatically be sent out

to each trap manager whose IP address has been defined. A total of five trap managers can be defined

in the system.

Contents

Main Mistral Lan Router ISDN with 4 Fast Ethernet ports + Broadband Interface Page Console Commands General Guidelines Express Mode vs. Advanced Mode Conventions Command Categories From a functional point of view, commands can be grouped into the following functional categories: Router> command (with parameters) Output Command List Bridging Commands Compression Commands DHCP Commands Diagnostic Commands Dial-in User Commands Filtering Commands IP Commands Port Commands Profile Commands Security Command SNMP Commands Statistics Commands System Commands Page Page show learning show learning <Interface Name> Compression Commands clear compression statistics <Profile Name> disable compression <Profile Name> enable compression <Profile Name> show compression statistics <Profile Name> DHCP Commands add dhcp entry <entry name> add dns <primary/secondary> <IP_addr> delete dhcp entry <entry name> delete dns <primary/secondary> disable dhcp enable dhcp set dhcp set range show dhcp show dhcp table show range Page test isdn <dial name> <64k/56k> Dial-in User Commands add user <profile name> (where profile name is a string <= 30 chars) Add the following Single Workstation dialing into the router using the CLI Advanced Mode delete user <profile name> Description: Deletes a dial-in user entry from the local user database. show user [profile name] Example 2: When a specific user is named, the output appears as follows: Filtering Commands add filter <1-8> delete filter <1-8> set filter default show filter show filter <1-8 > add pat entry <public port #> add pat entry default Page ping <ipAddr> [n_times] [n_size] set ip default route <gateway-ipAddr> set ip default route <Profile Name> set ip lan <ip_addr> <netMask> set ip private <ip_addr> <netMask> set ip rip [Interface Name] <disabled/passive/active> <rip1/rip2> set ip <Profile Name> set ip <Profile Name> < local-ipAddr> <netMask> <remote-ipAddr> 255.255.255.0. show arp table show icmp statistics show ip show ip <interface name> show ip routing table Host S Static Route G Gateway C Cloned Entry Example: show ip statistics Description: This csommand displays IP routing related statistics. Example: show pat show tcp statistics show udp statistics Port Commands clear port statistics [port name] disable port <port name> enable port <port name> set port <port name> show port show port <port name> Description: This command displays the configuration of a WAN interface port. Example 1: Example 2: show port statistics <port name> Example 1: Profile Commands add profile <Profile Name> clear profile statistics [Profile Name] connect profile <Profile Name> delete profile <Profile Name> disable profile <Profile Name> disconnect profile < Profile Name> enable profile <Profile Name> show profile show profile <Profile Name> Page disable trap enable trap set community string read <"password"> set trap manager <1-5> <ipAddr> show snmp statistics Page Page Page logout reset system save config set console baud <baudrate> set console timeout <1-60> set date <mm-dd-yy> set daylight time <on/off> set internet access time set log level <1-10> set prompt <prompt> set system contact <name> set system location <location information> set system name <system name> set time <hh:mm:ss> set timezone <-12 - +12> show config show connection log show interface list show internet access time show system show system log