Manuals / ATTO Technology / Computer Equipment / Network Card

ATTO Technology S-Class manual Appendix D Specifications Vii, Appendix E Warranty Viii

Models: S-Class

1 105

Download 105 pages 63.96 Kb

Page 9

10.0 System Monitoring and Reporting

79

RS-232 monitoring port and CLI

Ethernet monitoring port and CLI

Power On Self Test (POST)

Ready LED

Audible alarm

Thermal monitoring

Power supply monitoring

System fault LED and error codes

Disk drive activity and disk fault LEDs

10.1 Troubleshooting

82

Windows 2000 special instructions

Error messages

Specific situations and suggestions

If a drive fails to respond

If a power supply fails

To determine if the problem exists with the HIC

If you can’t access the CLI via Ethernet

If LUNs do not display on the host

10.2 Resetting Defaults		85
	Default
	To return to Default settings
	Factory Default
	To reset to factory defaults
Appendix A ATA Disk Technology		i
Appendix B	Information Commands Results	ii
Appendix C	Product Safety	vi
	Safety compliances
	EMC specifications
	Radio and television interference
Appendix D	Specifications	vii
	Environmental and physical
	Rack mount dimensions
	Floor mount dimensions
Appendix E	Warranty	viii
	Manufacturer limited warranty
	Contact ATTO Technology, Inc.

Image 9

ATTO Technology S-Class manual Appendix D Specifications Vii, Appendix E Warranty Viii

Contents

Diamond Storage Array Class Page Page Contents In-band CLI Over the Fibre Channel Serial Port Configuration Commands Configuring Drives RAID Interleave Parameters Appendix E Warranty Viii Appendix D Specifications ViiAtto Technology, Inc PrefacePage Diamond Storage Array Product Overview Diamond Storage Array featuresScsi model Fibre Channel modelDiamond Storage Array Technical Overview Adxt Powers ATA to New LevelsATA Interface Engine AIE The interface to each Physical setup Installation InstructionsSet up the Ethernet connection Connect to EthernetSet up RAID configuration Components Floor modelRack mount Components Spaced rail pairs in some rackmount cabinets Physical Set UpRack mount cabinets with stationary shelf or tray Sliding shelf or tray type systems should neverGeneral instructions Connecting a Fibre Channel Array AutoconfigurationManual configuration Fibre Channel connections To connect a Scsi array Connecting a Scsi ArrayBus speed, MB/sec Bus width Max. bus lengths Max. device BitsScsi connections Physical numbering Determining Drive and Sled DesignationsLogical numbering Numbering conventionsUnique serial number for each LUN ExamplesRAID Level 10 QuickRAID10 The QuickRAID10 RAID Level 5 QuickRAID5 with a fullyCommand Line Interface Accessing the ArrayAtto ExpressNAV RS-232 portSnmp In-band CLI Over the Fibre Channel DetailsInitiator Host Diamond Array Initiator/Host Diamond Storage Array Invalidparameterincdb will be returnedSerial Port Access Serial port access To connect to the Ethernet port Ethernet Access Telnet and Snmp ProtocolsTo use Telnet To use SnmpTraps are generated for the following situations Type SaveConfiguration restart to reboot the arrayBrowser compatibility Atto ExpressNAV Browser-based InterfaceOpening an ExpressNAV session Navigating ExpressNAVInformation Sidebar ExpressNAV Pages Clear Data ConfigurationLogical Units RebuildCommand Line Interface actions and responses Command Line Interface Use and GuidancePage Command Defaults Example Summary of CLI CommandsCommand Defaults Example General Use Commands General CLI commands Ethernet Commands TelnetPassword TelnetTimeoutTelnetUsername Fibre Channel Configuration Commands FcPortList FcPortInfoFcPortName FcWWNameSerialPortBaudRate Serial Port Configuration CommandsSerialPortHandshake SerialPortEchoSerial port CLI commands Diagnostic Commands Temperature SledFaultLEDSMARTData VirtualDriveInfoFcScsiBusyStatus Maintenance CommandsMaxEnclTempAlrm MinEnclTempAlrmMaintenance CLI commands Drive Configuration Commands IdeTransferRate DriveWipeLUNState QuickRAID0RAID5ClearData RestoreModePagesRAID5ClearDataStatus RAIDInterleaveExamples, refer to Information Commands Results on Configuring Drives Jbod Just a Bunch of DisksRAID Level Interleave Hot Spare sledsEnhancing performance Jbod To set up the Jbod configurationJbod Sled-based versus disk-based RAID LevelLUNs virtual drive numbers To remove RAID Level 0 groupsPage Page Type SaveConfiguration To set up RAID Level 1 groupsType SaveConfiguration Storage Management To remove RAID groupsType set QuickRAID 1 To set up RAID Level 1 with Hot Spare sledsConfiguring a fully-populated array To set up RAID Level 5 groupsTo set up one RAID Level 5 group with one Hot Spare sled Type set QuickRAID5 1 Type SaveConfiguration Restart To set up two RAID Level 5 groups with two Hot Spare sledsType set QuickRAID5 2 Type SaveConfiguration Restart LUN Removing RAID groups Type set QuickRAID5 ALL Type SaveConfiguration RestartType set QuickRAID10 0 1 2 To set up RAID Level 10 groupsType set QuickRAID10 1 Type SaveConfiguration Restart To set up RAID Level 10 with Hot Spare sledsRebuilding RAID Configurations To synchronize mirrored drives manually Set AutoRebuild disabled saveconfiguration restartTo change the RAID Interleave parameter RAID Interleave ParametersRAID interleave Hardware Maintenance Maintenance Disk drives Hot Swap Operating InstructionsPower supplies To replace a blower assemblyBlower assemblies Optional Hot Spare Sled Type set QuickRAID1 Type SaveConfiguration RestartVirtual Drive Hot Spare sleds To set up two RAID Level 5 groups with Hot Spare sledsCopying Drives ProcedureCopy drives Updating Firmware Updating firmware using the RS-232 serial portType put ....ima Cd c\diamond\flashSystem Monitoring and Reporting System fault LED and error codes Power supply monitoringNumber of blinks Troubleshooting Windows 2000 special instructions Error messagesCommand Line Interface messages Specific situations and suggestions Type FirmwareRestart If LUNs do not display on the hostDefault Resetting DefaultsFactory Default To return to Default settingsCommand Default Reset if default Reset during Chosen Fibre Channel FeatureDriveInfo sled ID drive ID Appendix B Information Commands ResultsV80DTESC Info allLunInfo LUNInfo LUNVirtualDriveInfo VirtualDriveInfo active planned Virtual Drive IDRadio and television interference Safety compliances EMC specificationsRack mount dimensions Floor mount dimensionsEnvironmental and physical Contact Atto Technology, Inc Manufacturer limited warranty