Direct IP-IP Audio Connections – Set to y, since Media Shuffling is enabled during the compliance test

 

add signaling-group 201

 

 

 

Page

1 of 1

 

 

 

 

 

 

SIGNALING GROUP

 

 

 

 

Group Number: 201

 

 

 

 

 

 

 

 

 

 

Group Type: sip

 

 

 

 

 

 

 

 

 

Transport Method: tls

 

 

 

 

IMS Enabled? n

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Near-end Node Name: CLAN

 

 

 

Far-end Node Name: SES

 

 

 

 

 

Near-end Listen Port: 5061

 

Far-end Listen Port: 5061

 

 

 

 

 

 

 

 

 

Far-end Network Region: 1

 

 

 

 

 

Far-end Domain: avaya.com

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bypass If IP Threshold Exceeded? n

 

 

Incoming Dialog Loopbacks: eliminate

 

 

RFC 3389 Comfort Noise? n

 

 

 

DTMF over IP: rtp-payload

 

 

Direct IP-IP Audio Connections? y

 

 

 

Session Establishment Timer(min): 3

 

 

IP Audio Hairpinning? n

 

 

 

Enable Layer 3 Test? n

 

 

Direct IP-IP Early Media? n

 

 

H.323 Station Outgoing Direct Media? n

 

 

Alternate Route Timer(sec): 6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.6. Configure SIP Trunk

This section describes the steps for administering a trunk group in Communication Manager for communication between Communication Manager and SIP Enablement Services. Enter the add trunk-group <t> command, where t is an unallocated trunk group and configure the following:

Group Type – Set the Group Type field to sip.

Group Name – Enter a descriptive name.

TAC (Trunk Access Code) – Set to any available trunk access code.

Signaling Group – Set to the Group Number field value configured in Section 5.5.

Number of Members – Allowed value is between 0 and 255. Set to a value large enough to accommodate the number of SIP telephone extensions being used.

Note: Each SIP call between two SIP endpoints (whether internal or external) requires two SIP trunks for the duration of the call. The license file installed on the system controls the maximum permitted.

 

add trunk-group 201

 

 

 

 

Page

1 of 21

 

 

 

 

 

 

TRUNK GROUP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Group Number:

201

 

 

Group Type: sip

 

 

CDR Reports: y

 

 

 

Group Name: To SES

 

 

COR: 1

 

 

TN: 1

TAC: 116

 

 

 

 

Direction: two-way

Outgoing Display? y

 

 

 

 

 

 

 

 

 

Dial Access? n

 

Night Service:

 

 

 

 

 

 

Queue Length: 0

 

 

 

 

 

 

 

 

 

 

 

Service Type: tie

 

Auth Code? n

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signaling Group: 201

 

 

 

 

 

 

 

 

 

 

Number of Members: 10

 

 

CRK; Reviewed:

Solution & Interoperability Test Lab Application Notes

10 of 21

SPOC 7/1/2011

©2011 Avaya Inc. All Rights Reserved.

Polycom8400-SES

Page 10
Image 10
Avaya 8400-SES manual Configure SIP Trunk, Signaling Group, Trunk Group