Routerconfigure# interface interface-name | Avaya P3343T-ML specification

Router(configure)# interface <interface-name>

Chapter 12 Avaya P330 Layer 3 Features

VLAN number, and <Vlan-name>by the VLAN name. Press Enter.

7Create an IP interface name. Type:

Router(configure)# interface <interface-name>

Press Enter.

The Router(configure-if:<interface-name>)# prompt appears.

8Assign the IP address and network mask of the IP interface you have created. Use the command:

Router(configure-if:<interface-name>)# ip address <ip- address> <netmask>

Press Enter

9Assign a vlan to the IP interface you have created. Type: Assign a vlan to the IP interface you have created. Type:

Router(configure)# interface <interface-name># ip vlan <vland-id>

Press Enter.

10Type exit and press Enter. This returns you to the prompt:

Router(configure)#

11If the management station is not on the same subnet as the switch, configure a default gateway (static route). Use the command:

ip default-gateway<ip-address>and press Enter, replacing <ip-address>with the IP address of the default gateway.

12Save the configuration changes by typing copy running-configstartup-configand press Enter.

Obtaining and Activating a License Key

In order to benefit from Layer 3 Routing functionality, it is required that you either purchase a Layer 3 preconfigured P330-ML module or a Routing License Key Certificate for the P330-ML.

Each Certificate is specific for:

•The module type.

•The required feature.

•The number of devices.

After you purchase a Routing Licence Key Certificate, you must obtain and activate a Routing License Key.

126	Avaya P334T-ML User’s Guide

Image 142

Avaya P3343T-ML manual Routerconfigure# interface interface-name, The Routerconfigure-ifinterface-name# prompt appears

Contents

Installation and Configuration Guide STACKABLE SWITCHSOFTWARE VERSION AVAYA P334T-ML avaya.com Document no Section ContentsOverview Installation Configuring the Terminal Serial Port Parameters Configuration Ingress VLAN Security Port Mirroring Constraints Troubleshooting and Maintenance Chapter 15 Updating the Software Preface Before you Install the P330-MLSafety Information FCC Notice Warranty Notes, Cautions, and Warnings Avaya Support Avaya P334T-ML User’s Guide SECTION 1 OVERVIEW Page Chapter Avaya P334T-ML FeaturesAvaya P334T-ML Overview Introduction Network Management and Monitoring Layer 3 Features P330-MLCommand Line Interface CLI Device Manager Embedded Web Port Mirroring Avaya Integrated ManagerSMON Fans, Power Supply, and BUPS-ML Monitoring IEEE Standards and CompatibilityAvaya P330 Standards Supported IETF - Layer IETF - Network Monitoring Power Requirements SpecificationsP334T-ML Switch Physical Safety - DC Version SafetySafety - AC Version EMC Emissions Interfaces Stacking Sub-moduleBasic MTBF Safety Information Approved SFF/SFP GBIC Transceivers To Install the SFF/SFP GBIC transceiver InstallationSpecifications To Remove the SFF/SFP GBIC transceiver Gigabit Fiber Optic Cabling Agency Approval Console Pin Assignments Chapter SECTION 2 INSTALLATION Page Required Tools InstallationSite Preparation Table 4.2 Power Requirements - AC Power Requirements - DC Rack Mounting Optional Connecting Stacked Switches Installing the X330STK-ML Stacking Sub-Module OptionalTo connect stacked switches 5 Power up the added modules X330SC X330RCX330LC Making Connections to Network Equipment Connecting Cables to Network EquipmentPrerequisites Page Powering On - Avaya P330 Module AC Powering Up the Avaya P330Powering On - Avaya P330 Switch DC Post-Installation Avaya P334T-ML Front and Rear Panels Avaya P334T-ML Front Panel P334T-ML LEDs LED Name Chapter 6 Avaya P334T-ML Front and Rear Panels Avaya P334T-ML LED Descriptions Continued Table 6.2 Avaya P334T-ML - - Select buttons Avaya P334T-ML Back PanelBUPS-ML connector cover plate removed Figure 6.4 P334T-ML AC version Back Panel with Stacking Sub-module BUPS-ML Input Connector Figure 6.6 BUPS-ML Input Connector Sticker Connecting a Terminal to the Avaya P330 Serial port Establishing Switch AccessConfiguring the Terminal Serial Port Parameters Establishing a Serial Connection session router P330 SessionsAssigning P330’s IP Stack Address The mode can be either switch, router, wan, atm, mgp Establishing a Telnet Connection Establishing an SSH Connection Establishing a Modem PPP Connection with the P330 Connecting a Modem to the Console Portset interface ppp enable Overview Security Levels Entering the Supervisor Level Entering the CLI SNMP Support User AuthenticationIntroduction to SNMP control the P330 Users Groups SNMP Commands Views In order to In order to SSH Protocol Support Introduction to SSH SSH Commands Figure 8.1 SSH Session Establishment Process SCP Protocol Support RADIUS Introduction to RADIUS sent to switch User attempts login Local User account authenticated in switch? NoUser name and password authenticated? No Authentication Reject Authentication request sent to RADIUS Server Radius Commands Telnet Client Support Telnet CommandsIntroduction to Telnet Recovery Password Commands Recovery PasswordIntroduction Allowed Managers Allowed Managers CLI CommandsAllowed Managers Introduction Allowed Protocols Allowed Protocols CLI CommandsAllowed Protocols Introduction ip telnet-client enable no ip telnet-client SECTION 3 CONFIGURATION Page Configuring the Switch P330 Default SettingsAvaya P330 Default Settings Function Ports 1 Ensure that the other side is also set to Autonegotiation EnabledPorts 51 Chapter 9 P330 Default Settings Switch Configuration Basic Switch Configuration Identifying the system System Parameter ConfigurationOperating parameters Uploading and Downloading Device Configurations and Images Network Time Acquiring Protocols Parameter Configuration Layer 2 Configuration File In order to Layer 3 Configuration File In order to System Logging System Logging Introduction Sinks Applications Syslog Servers Syslog Configuration CLI Commands In order to Monitoring CPU Utilization Chapter 10 Switch Configuration Avaya P330 Layer 2 Features Overview Fast Ethernet Configuring Ethernet ParametersEthernet Gigabit Ethernet Gigabit Ethernet ports MMMMMMSSSSSS MM-MM-MM-SS-SS-SS Ethernet Configuration CLI Commands Priority queuing - 10/100 ports 4 queues 1G ports 2 queues Ethernet Implementation in the Avaya P334T-MLSpeed - 10/100 ports 1-48 1G ports 51 CAM size - 8K addresses VLAN Configuration VLAN Overview VLAN Tagging Multi VLAN Binding Figure 11.3 illustrates these binding modes in P330 Automatic VLAN Learning VLAN CLI CommandsIngress VLAN Security VLAN Implementation in the Avaya P334T-ML How “Port Based” Authentication Works Port Based Network Access Control PBNACPBNAC Implementation in the P330 Family Configuring the P330 for PBNAC PBNAC CLI Commands In order to Spanning Tree Protocol Spanning Tree ProtocolSpanning Tree per Port Rapid Spanning Tree Protocol RSTP Spanning Tree Implementation in the P330 Family Spanning Tree Protocol CLI Commands admin and operational RSTP status Set the port point-to-point adminset port point-to-point admin status MAC Security MAC Security Implementation in P330 MAC Security CLI Commands MAC Aging CLI Commands Configuring the P330 for MAC AgingMAC Aging LAG CLI Commands LAG Overview LAG Implementation in the Avaya P330 Family of Products Port Redundancy Port Redundancy Operation Port Redundancy CLI Commands Intermodule Port Redundancy show intermodule port redundancy display the intermoduleredundancy entry defined for the IP Multicast Filtering IP Multicast CLI Commands IP Multicast Implementation in the Avaya P334T-ML RMON RMON CLI CommandsRMON Overview In order to SMON SMON Overview Port Mirroring Overview Port Mirroring ConfigurationPort Mirroring CLI commands Port Mirroring Constraints Multilayer Policy About Multilayer Policy Multilayer Policy Implementation in the P334T-ML Configuring the P334T-ML for Multilayer Policy Multilayer Policy CLI Commands In order to Implementation of Weighted Queuing in the P330-ML Weighted QueuingWeighted Queuing CLI Commands Port Classification CLI Commands Port Classification Stack Health Stack RedundancyImplementation of Stack Health in the P330 Family procedure Stack Health CLI CommandsInitiate the stack health testing set stack health Chapter 11 Avaya P330 Layer 2 Features Avaya P330 Layer 3 Features What is Routing? Figure 12.1 Routing Forwarding Routing ConfigurationMultinetting Multiple Subnets per VLAN IP Configuration IP Configuration CLI Commands Assigning Initial Router Parameters set vlan Vlan-id name Vlan-name replacing Vlan-id by the Routerconfigure-ifinterface-name# ip address ip- address netmask Routerconfigure# interface interface-nameThe Routerconfigure-ifinterface-name# prompt appears Routerconfigure# interface interface-name# ip vlan vland-id 1 Go to http//license-lsg.avaya.com and click “request new license” Obtaining a Routing License KeyTo obtain a License Key that enables routing features 2 Enter the Certificate Key and Certificate Type 3 Click Next 4 Enter contact information once per certificate 5 Click Next 6 View number of licenses left License Key CLI Commands set license module license featureNameActivating a Routing License Key Chapter 12 Avaya P330 Layer 3 Features RIP Routing Interchange Protocol Configuration RIP Overview RIP2 RIP CLI CommandsTable 12.1 DIfferences Between RIP and RIP2 In order to OSPF Open Shortest Path First Configuration OSPF Overview OSPF CLI Commands Static Routing Configuration CLI Commands Static Routing ConfigurationStatic Routing Overview Route Preferences Route Redistribution Commands Route Redistribution ARP Address Resolution Protocol Table Configuration ARP Overview ARP CLI Commands The ARP Table BOOTP/DHCP Dynamic Host Configuration Protocol Relay Configuration BOOTP/DHCP Overview BOOTP/DHCP CLI Commands NetBIOS Overview NetBIOS Re-broadcast ConfigurationNetBIOS Re-broadcast Configuration CLI Commands VRRP Virtual Router Redundancy Protocol Configuration VRRP Overview VRRP Configuration Example VRRP CLI Commands Case #2 In order to SRRP Configuration Example SRRP ConfigurationSRRP Overview SRRP CLI Commands Policy Configuration Overview Policy ConfigurationPolicy Configuration CLI Commands In order to Policy Configuration Example Figure 12.4 Avaya P330 Policy P330-1super# ip access-list 100 2 fwd3 tcp any host P330-1super# ip access-list 100 1 fwd6 tcp 149.49.0.0 0.0.255.255 anyP330-1super# ip access-list 100 3 deny tcp host 192.168.5.33 any eq IP Fragmentation and Reassembly Overview IP Fragmentation and ReassemblyIP Fragmentation/Reassembly CLI Commands SECTION 4 TROUBLESHOOTING AND MAINTENANCE Page Troubleshooting the Installation Troubleshooting the Installation Chapter 13 Troubleshooting the Installation Maintenance Replacing the Stacking Sub-module Maintenance Obtain Software Online Updating the SoftwareSoftware Download Downloading Software Download New Version without Overwriting Existing Version