Manuals / Avaya / Computer Equipment / Switch

Avaya P3343T-ML manual Establishing a Modem PPP Connection with the P330, Overview

Models: P3343T-ML

1 178

Download 178 pages 4.71 Kb

Page 52

Establishing a Modem (PPP) Connection with the P330

Chapter 7 Establishing Switch Access

5When you are prompted for a password, enter the User Level password root in lower case letters (do NOT use uppercase letters). The User level prompt will appear when you have established communications with the Avaya P330.

Establishing a Modem (PPP) Connection with the P330

Overview

Point-to-Point Protocol (PPP) provides a Layer 2 method for transporting multi-protocol datagrams over modem links.

Connecting a Modem to the Console Port

A PPP connection with a modem can be established only after the Avaya P330 is configured with an IP address and net-mask, and the PPP parameters used in the Avaya P330 are compatible with the modem’s PPP parameters.

1Connect a terminal to the console port of the Avaya P330 switch as described in Connecting a Terminal to the Avaya P330 Serial port.

2When you are prompted for a Login Name, enter the default name root.

3When you are prompted for a password, enter the password root. You are now in Supervisor Level.

4At the prompt, type:

set interface ppp <ip_addr> <net-mask>

with an IP address and netmask to be used by the Avaya P330 to connect via its PPP interface.

The PPP interface configured with the set interface ppp command must be on a different subnet from the stack inband interface.

5Set the baud rate, ppp authentication, and ppp time out required to match your modem. These commands are described in the Avaya P330: Reference Guide.

6At the prompt, type:

set interface ppp enable

The CLI responds with the following:

Entering the Modem mode within 60 seconds...

Please check that the proprietary modem cable is plugged into the console port

7Use the DB-25 to RJ-45 connector to plug the console cable to the modem’s DB-25 connector. Plug the other end of the cable RJ-45 connector to the Avaya P330 console’s RJ-45 port.

8The Avaya P330 enters modem mode.

9You can now dial into the switch from a remote station, and open a Telnet session to the PPP interface IP address.

36	Avaya P334T-ML User’s Guide

Image 52

Avaya P3343T-ML manual Establishing a Modem PPP Connection with the P330, Overview, Connecting a Modem to the Console Port

Contents

STACKABLE SWITCH SOFTWARE VERSIONInstallation and Configuration Guide AVAYA P334T-MLavaya.com Document noSection ContentsOverview Installation SectionConfiguring the Terminal Serial Port Parameters Configuration SectionIngress VLAN Security Port Mirroring Constraints Troubleshooting and Maintenance SectionChapter 15 Updating the Software Before you Install the P330-ML Safety InformationPreface FCC NoticeWarranty Notes, Cautions, and WarningsAvaya Support Avaya P334T-ML User’s GuideAvaya P334T-ML User’s Guide SECTION 1 OVERVIEW Page Avaya P334T-ML Features Avaya P334T-ML OverviewChapter IntroductionLayer 3 Features P330-ML Command Line Interface CLINetwork Management and Monitoring Device Manager Embedded WebPort Mirroring Avaya Integrated ManagerSMON Chapter 1 Avaya P334T-ML Overview Fans, Power Supply, and BUPS-ML MonitoringAvaya P334T-ML User’s Guide Standards and Compatibility Avaya P330 Standards SupportedIEEE IETF - LayerIETF - Network Monitoring Specifications P334T-ML SwitchPower Requirements PhysicalSafety Safety - AC VersionSafety - DC Version EMC EmissionsStacking Sub-module InterfacesBasic MTBF Basic MTBFSafety Information Approved SFF/SFP GBIC TransceiversInstallation SpecificationsTo Install the SFF/SFP GBIC transceiver To Remove the SFF/SFP GBIC transceiverGigabit Fiber Optic Cabling Agency ApprovalConsole Pin Assignments Chapter Avaya P334T-ML User’s GuideSECTION 2 INSTALLATION Page Installation Required ToolsSite Preparation ChapterTable 4.2 Power Requirements - AC Power Requirements - DCRack Mounting Optional Connecting Stacked Switches Installing the X330STK-ML Stacking Sub-Module OptionalTo connect stacked switches 5 Power up the added modules Installation ChapterAvaya P334T-ML User’s Guide X330RCMaking Connections to Network Equipment Connecting Cables to Network EquipmentPrerequisites Page Powering Up the Avaya P330 Powering On - Avaya P330 Module ACPowering On - Avaya P330 Switch DC ChapterPost-Installation Avaya P334T-ML Front Panel Avaya P334T-ML Front and Rear PanelsChapter P334T-ML LEDs LED NameChapter 6 Avaya P334T-ML Front and Rear Panels Avaya P334T-ML LED Descriptions Continued Avaya P334T-ML Back Panel BUPS-ML connector cover plate removedTable 6.2 Avaya P334T-ML - - Select buttons Figure 6.4 P334T-ML AC version Back Panel with Stacking Sub-moduleBUPS-ML Input Connector Figure 6.6 BUPS-ML Input Connector StickerChapter 6 Avaya P334T-ML Front and Rear Panels Avaya P334T-ML User’s GuideEstablishing Switch Access Configuring the Terminal Serial Port ParametersConnecting a Terminal to the Avaya P330 Serial port Establishing a Serial ConnectionP330 Sessions Assigning P330’s IP Stack Addresssession router The mode can be either switch, router, wan, atm, mgpEstablishing a Telnet Connection Establishing an SSH ConnectionConnecting a Modem to the Console Port set interface ppp enableEstablishing a Modem PPP Connection with the P330 OverviewSecurity Levels Entering the Supervisor LevelEntering the CLI User Authentication SNMP SupportIntroduction to SNMP Chaptercontrol the P330 Users Groups SNMP Commands ViewsIn order to In order to SSH Protocol Support Introduction to SSHSSH Commands Figure 8.1 SSH Session Establishment ProcessSCP Protocol Support RADIUS Introduction to RADIUSChapter 8 User Authentication User attempts login Local User account authenticated in switch? NoUser name and password authenticated? No Authentication Reject sent to switchRadius Commands Telnet Client Support Telnet CommandsIntroduction to Telnet Recovery Password Commands Recovery PasswordIntroduction Allowed Managers Allowed Managers CLI CommandsAllowed Managers Introduction Allowed Protocols Allowed Protocols CLI CommandsAllowed Protocols Introduction Use the following command Enable Telnet access from theip telnet-client enable switchSECTION 3 CONFIGURATION Page P330 Default Settings Configuring the SwitchAvaya P330 Default Settings ChapterFunction Ports 1 Ensure that the other side is also set to Autonegotiation EnabledPorts 51 Chapter 9 P330 Default Settings Avaya P334T-ML User’s GuideSwitch Configuration Basic Switch ConfigurationChapter IntroductionIdentifying the system System Parameter ConfigurationOperating parameters Uploading and Downloading Device Configurations and Images Network Time Acquiring Protocols Parameter ConfigurationLayer 2 Configuration File In order to Layer 3 Configuration File In order to System Logging System Logging IntroductionSinks ApplicationsSyslog Servers Syslog Configuration CLI Commands In order to Monitoring CPU Utilization Chapter 10 Switch Configuration Avaya P334T-ML User’s GuideOverview Avaya P330 Layer 2 FeaturesChapter Configuring Ethernet Parameters EthernetFast Ethernet Gigabit EthernetGigabit Ethernet ports MMMMMMSSSSSS MM-MM-MM-SS-SS-SS Ethernet Configuration CLI Commands Ethernet Implementation in the Avaya P334T-ML Chapter 11 Avaya P330 Layer 2 FeaturesSpeed - 10/100 ports 1-48 1G ports 51 Priority queuing - 10/100 ports 4 queues 1G ports 2 queuesVLAN Configuration VLAN OverviewVLAN Tagging Multi VLAN BindingFigure 11.3 illustrates these binding modes in P330 Automatic VLAN Learning VLAN CLI CommandsIngress VLAN Security VLAN Implementation in the Avaya P334T-ML How “Port Based” Authentication Works Port Based Network Access Control PBNACPBNAC Implementation in the P330 Family Configuring the P330 for PBNAC PBNAC CLI Commands In order to Spanning Tree Protocol Spanning Tree ProtocolSpanning Tree per Port OverviewRapid Spanning Tree Protocol RSTP Spanning Tree Implementation in the P330 Family Spanning Tree Protocol CLI Commands Use the following command Set the port point-to-point adminset port point-to-point admin admin and operational RSTP statusMAC Security MAC Security Implementation in P330MAC Security CLI Commands Configuring the P330 for MAC Aging MAC Aging CLI CommandsMAC Aging OverviewLAG CLI Commands LAG OverviewLAG Implementation in the Avaya P330 Family of Products Port Redundancy Port Redundancy OperationPort Redundancy CLI Commands Intermodule Port RedundancyUse the following command switchChapter 11 Avaya P330 Layer 2 Features In order toIP Multicast Filtering OverviewIP Multicast CLI Commands IP Multicast Implementation in the Avaya P334T-MLRMON RMON CLI CommandsRMON Overview In order to SMON SMON OverviewPort Mirroring Configuration Port Mirroring CLI commandsPort Mirroring Overview Port Mirroring ConstraintsMultilayer Policy About Multilayer PolicyMultilayer Policy Implementation in the P334T-ML Configuring the P334T-ML for Multilayer Policy Multilayer Policy CLI Commands In order to Implementation of Weighted Queuing in the P330-ML Weighted QueuingWeighted Queuing CLI Commands Port Classification Port Classification CLI CommandsOverview Stack Redundancy Stack HealthImplementation of Stack Health in the P330 Family OverviewStack Health CLI Commands Use the following commandInitiate the stack health testing procedureChapter 11 Avaya P330 Layer 2 Features Avaya P334T-ML User’s GuideAvaya P330 Layer 3 Features What is Routing?Chapter IntroductionFigure 12.1 Routing Forwarding Routing ConfigurationMultinetting Multiple Subnets per VLAN IP Configuration IP Configuration CLI CommandsAssigning Initial Router Parameters set vlan Vlan-id name Vlan-name replacing Vlan-id by theRouterconfigure# interface interface-name The Routerconfigure-ifinterface-name# prompt appearsRouterconfigure-ifinterface-name# ip address ip- address netmask Routerconfigure# interface interface-name# ip vlan vland-idObtaining a Routing License Key To obtain a License Key that enables routing featuresChapter 12 Avaya P330 Layer 3 Features 1 Go to http//license-lsg.avaya.com and click “request new license”Chapter 12 Avaya P330 Layer 3 Features 4 Enter contact information once per certificate 5 Click Next6 View number of licenses left Avaya P334T-ML User’s GuideLicense Key CLI Commands set license module license featureNameActivating a Routing License Key Chapter 12 Avaya P330 Layer 3 Features Avaya P334T-ML User’s GuideRIP Routing Interchange Protocol Configuration RIP OverviewRIP2 RIP CLI CommandsTable 12.1 DIfferences Between RIP and RIP2 In order to OSPF Open Shortest Path First Configuration OSPF OverviewOSPF CLI Commands Static Routing Configuration CLI Commands Static Routing ConfigurationStatic Routing Overview Route Preferences Route Redistribution Commands Route RedistributionARP Address Resolution Protocol Table Configuration ARP OverviewARP CLI Commands The ARP TableBOOTP/DHCP Dynamic Host Configuration Protocol Relay Configuration BOOTP/DHCP OverviewBOOTP/DHCP CLI Commands NetBIOS Overview NetBIOS Re-broadcast ConfigurationNetBIOS Re-broadcast Configuration CLI Commands VRRP Virtual Router Redundancy Protocol Configuration VRRP OverviewVRRP Configuration Example VRRP CLI Commands Case #2In order to SRRP Configuration Example SRRP ConfigurationSRRP Overview SRRP CLI Commands Policy Configuration Overview Policy ConfigurationPolicy Configuration CLI Commands In order to Policy Configuration Example Figure 12.4 Avaya P330 PolicyP330-1super# ip access-list 100 1 fwd6 tcp 149.49.0.0 0.0.255.255 any P330-1super# ip access-list 100 2 fwd3 tcp any hostP330-1super# ip access-list 100 3 deny tcp host 192.168.5.33 any eq Policy Configuration ExampleIP Fragmentation and Reassembly Overview IP Fragmentation and ReassemblyIP Fragmentation/Reassembly CLI Commands SECTION 4 TROUBLESHOOTING AND MAINTENANCE Page Troubleshooting the Installation Troubleshooting the InstallationChapter Chapter 13 Troubleshooting the Installation Avaya P334T-ML User’s GuideMaintenance Replacing the Stacking Sub-moduleChapter IntroductionChapter MaintenanceAvaya P334T-ML User’s Guide Updating the Software Software DownloadObtain Software Online Downloading SoftwareDownload New Version without Overwriting Existing Version