Bad Boy Mowers 02.9812.0001C Equipment Handling

BAD BOY™ SPOT LUMINAIRE USER MANUAL

58 02.9812.0001C

Equipment Handling

Proper Lamp Servicing and Operation

Servicing

• When handling a lamp, hold it by the ceramic base while wearing cotton gloves or finger cots. Do

not touch the glass envelope (bulb). If you touch the glass with bare fingers, wipe off any

fingerprints with alcohol.

Heat

• When lamps are lit, the interior of the luminaires becomes very hot. To aid in the airflow

circulation within the luminaires, after dousing the lamps, wait 5 minutes before removing power

to the luminaires. This will provide enough time for the equipment fan to cool off the unit.

Lamp Life

• When operating arc lamps, allow luminaires to operate for at least 3 minutes. It takes about 3

minutes for the fill components (mercury and halogen-metal compounds) in the lamp tubes to

vaporize completely. If the lamps are switched off earlier than 3 minutes, the fill components are

partially vaporized. The inadequately vaporized fill components and the electrode material

(tungsten) are deposited in the areas of the lamp tubes that have remained cool. As a result, the

lamp tubes blacken prematurely and reduce the service lives of the lamps.

• If system will be unattended for more than 3-4 hours, luminaire lamps should be doused.

• The Bad Boy lamp indicator (available on the menu Home screen) displays total lamp hours.

Lamp hours are shown in green if under threshold, yellow at 750 hours, and red at 900 hours. It is

mandatory that the lamp be changed before 900 hours.

CAUTION: It is mandatory that the lamp be changed before 900 hours.

Contents

Main USER MANUAL Page F Compliance Notice Safety Notice FCC Page F Notes de scurit iv Revision History This manual has been revised as follows: Table of Contents Introduction Chapter 1. Description Chapter 2. Installation Chapter 3. Operation Chapter 4. Troubleshooting and Maintenance Appendix A. Technical Specifications Appendix B. Glossary Page Introduction About This Manual Additional Documentation 2 Customer Service For additional resources and documentation, please visit our website at: www.prg.com Gobo Art Submission Guidelines Page Page Features Overview Features DESCRIPTION : COMPONENTS Components Included Items The following illustration shows all items included with the luminaire: Figure 1-1: Bad Boy Luminaire Included Items Replacement Items and Accessories Major Components and Controls Ethernet Input Power Connector Upper Enclosure Detail DMX512 Thru Installation Power and Data Cabling Requirements Power Data DMX512 Cables I NSTALLATION : POWER AND D ATA C The XLR 5-pin connectors should be wired as follows: * Characteristic Impedance Table 2-1: Recommended Cable Types DMX512 Male Termination Connector Ethernet Cables Installation Procedures Unpacking and Attaching Hanging Brackets Standard Hang I NSTALLATION : INSTALLATION P Step 6. Connect power and data cables according to "Connecting Power and Data" on page 19. Figure 2-5: Standard Hanging Configuration and Dimensions Vertical "Yoke Out" Hang I NSTALLATION : INSTALLATION P Figure 2-7: Vertical "Yoke Out" Hanging Configuration 1 2 Standing Position Connecting Power and Data 20 Ethernet Ethernet Power In Power In Power In Ethernet Power Up and Basic Setup Procedures Powering Up the Luminaire Comm LED Operation Bypassing Calibration Setting a Starting Address DMX Comm Ethernet (Art-Net) Comm Starting the Lamp Configuring Comm Loss Setting Configuring Universe, Comm, and Other Options Accessory Options Follow Spot Operation Enabling Pan/Tilt Free Mode Page Menu System Using the Menu Touchscreen On-Board Battery Menu System Overview Menu Details Home Screen Lamp Screen Configuration Screen Pan/Tilt Screen Information Screen Communication Screen Status Screen Test Screen 38 DMX512 Operation Channel Mapping Table 3-1: DMX512 Channel Mapping Wheel Control 40 The diagram below illustrates the wheel control modes, using the Color Wheel as an example: Figure 3-4: Wheel Control Modes Table 3-5: Strobe Control 0-9 continuous 10-19 discrete 20-39 spin 47-49 fast random Control Channel Wheel Channel wheel choice direction/speed OPERATION : DMX512 OPERATION Control Channels Timing Channels Channel Functions Timing Channel Mapping OPERATION : DMX512 OPERATION Table 3-8: Timing Channels 44 OPERATION : DMX512 OPERATION Zoom Tables Gobo Set Zero Position Page 48 Troubleshooting Troubleshooting Guide The following table provides a list of common start-up problems and possible solutions. Errors 50 Mechanism Errors Errors will be shown after the mechanism code, for example: PAN:Comm Error. T Other Errors Testing Test Screen Mechanical Test Group Test Software Update Software Update Using LumLoader Application Page Software Crossload Equipment Handling Proper Lamp Servicing and Operation Routine Maintenance Removing the Head Covers Page Removing the Aft Cover Removing the Enclosure Covers Cleaning the Head Electrostatic Filters Cleaning the Enclosure Intake Filters Cleaning the Luminaire Exterior Cleaning the Lenses Page Figure 4-7: Accessing Zoom Lens Assembly 68 Cleaning Gobo, Color and Dimmer Wheels Replacing the Lamp Page Adjusting the Lamp Replacing a Gobo Page T ROUBLESHOOTING AND M AINTENANCE : ROUTINE M CAUTION: The gobos must be seated properly, especially the gear mesh. Figure 4-12: Gobo Positions and Alignment Replacing a Designer Color Filter Page Page Page Bad Boy Spot Luminaire TECHNICAL SPECIFICATIONS Bad Boy Road Case AC Line Current / Power vs. Voltage Photometric Data 84 Narrow Zoom 8 Full Angle 40,000 beam Lumens Medium Zoom 34 Full Angle 48,000 beam Lumens 86 Wide Zoom 56 Full Angle 50,000 beam Lumens TECHNICAL SPECIFICATIONS Logarithmic Beam Illuminance Comparison 8, 34 and 56 Zoom settings. Operation at Reduced Power Page Page Glossary of Terms B