Bad Boy Mowers 02.9812.0001C Replacing a Gobo

TROUBLESHOOTING AND MAINTENANCE : ROUTINE MAINTENANCE

02.9812.0001C 73

4

Replacing a Gobo

Parts:

Standard or Custom Gobo(s), as required

Tools and Supplies:

#2 Phillips screwdriver

Cotton gloves or finger cots

WARNING: Remove power from luminaire before performing any maintenance procedures.

To replace a gobo:

Step 1. Remove power from luminaire.

Step 2. Locate appropriate head cover door for access to Rotating Gobo Wheel 1 (R1) or Rotating

Gobo Wheel 2 (R2) as shown in Figure 4-10. (Doors are identified by a label.) Turn captive

screw to open door.

CAUTION: Do not touch gobos with bare fingers. Wear cotton gloves or finger cots when handling.

Step 3. Rotate wheel until desired gobo is accessible.

Step 4. Rotate Color Wheels so that their "open" position lines up next to the gobo you wish to

replace. (This will avoid potential damage to the adjacent wheels as the gobo is being

replaced.)

Figure 4-10: Accessing Gobo and Designer Color Wheels

Head Cover Door

R1 Wheel Access

Head Cover Door

R2 and Designer Wheel Access

X

Z

Captive Screw

Captive Screw

Contents

Main USER MANUAL Page F Compliance Notice Safety Notice FCC Page F Notes de scurit iv Revision History This manual has been revised as follows: Table of Contents Introduction Chapter 1. Description Chapter 2. Installation Chapter 3. Operation Chapter 4. Troubleshooting and Maintenance Appendix A. Technical Specifications Appendix B. Glossary Page Introduction About This Manual Additional Documentation 2 Customer Service For additional resources and documentation, please visit our website at: www.prg.com Gobo Art Submission Guidelines Page Page Features Overview Features DESCRIPTION : COMPONENTS Components Included Items The following illustration shows all items included with the luminaire: Figure 1-1: Bad Boy Luminaire Included Items Replacement Items and Accessories Major Components and Controls Ethernet Input Power Connector Upper Enclosure Detail DMX512 Thru Installation Power and Data Cabling Requirements Power Data DMX512 Cables I NSTALLATION : POWER AND D ATA C The XLR 5-pin connectors should be wired as follows: * Characteristic Impedance Table 2-1: Recommended Cable Types DMX512 Male Termination Connector Ethernet Cables Installation Procedures Unpacking and Attaching Hanging Brackets Standard Hang I NSTALLATION : INSTALLATION P Step 6. Connect power and data cables according to "Connecting Power and Data" on page 19. Figure 2-5: Standard Hanging Configuration and Dimensions Vertical "Yoke Out" Hang I NSTALLATION : INSTALLATION P Figure 2-7: Vertical "Yoke Out" Hanging Configuration 1 2 Standing Position Connecting Power and Data 20 Ethernet Ethernet Power In Power In Power In Ethernet Power Up and Basic Setup Procedures Powering Up the Luminaire Comm LED Operation Bypassing Calibration Setting a Starting Address DMX Comm Ethernet (Art-Net) Comm Starting the Lamp Configuring Comm Loss Setting Configuring Universe, Comm, and Other Options Accessory Options Follow Spot Operation Enabling Pan/Tilt Free Mode Page Menu System Using the Menu Touchscreen On-Board Battery Menu System Overview Menu Details Home Screen Lamp Screen Configuration Screen Pan/Tilt Screen Information Screen Communication Screen Status Screen Test Screen 38 DMX512 Operation Channel Mapping Table 3-1: DMX512 Channel Mapping Wheel Control 40 The diagram below illustrates the wheel control modes, using the Color Wheel as an example: Figure 3-4: Wheel Control Modes Table 3-5: Strobe Control 0-9 continuous 10-19 discrete 20-39 spin 47-49 fast random Control Channel Wheel Channel wheel choice direction/speed OPERATION : DMX512 OPERATION Control Channels Timing Channels Channel Functions Timing Channel Mapping OPERATION : DMX512 OPERATION Table 3-8: Timing Channels 44 OPERATION : DMX512 OPERATION Zoom Tables Gobo Set Zero Position Page 48 Troubleshooting Troubleshooting Guide The following table provides a list of common start-up problems and possible solutions. Errors 50 Mechanism Errors Errors will be shown after the mechanism code, for example: PAN:Comm Error. T Other Errors Testing Test Screen Mechanical Test Group Test Software Update Software Update Using LumLoader Application Page Software Crossload Equipment Handling Proper Lamp Servicing and Operation Routine Maintenance Removing the Head Covers Page Removing the Aft Cover Removing the Enclosure Covers Cleaning the Head Electrostatic Filters Cleaning the Enclosure Intake Filters Cleaning the Luminaire Exterior Cleaning the Lenses Page Figure 4-7: Accessing Zoom Lens Assembly 68 Cleaning Gobo, Color and Dimmer Wheels Replacing the Lamp Page Adjusting the Lamp Replacing a Gobo Page T ROUBLESHOOTING AND M AINTENANCE : ROUTINE M CAUTION: The gobos must be seated properly, especially the gear mesh. Figure 4-12: Gobo Positions and Alignment Replacing a Designer Color Filter Page Page Page Bad Boy Spot Luminaire TECHNICAL SPECIFICATIONS Bad Boy Road Case AC Line Current / Power vs. Voltage Photometric Data 84 Narrow Zoom 8 Full Angle 40,000 beam Lumens Medium Zoom 34 Full Angle 48,000 beam Lumens 86 Wide Zoom 56 Full Angle 50,000 beam Lumens TECHNICAL SPECIFICATIONS Logarithmic Beam Illuminance Comparison 8, 34 and 56 Zoom settings. Operation at Reduced Power Page Page Glossary of Terms B