Manuals / Bard / Household Appliance / Furnace

Bard Complete Beckett Genisys 7505 Manual and Installation Guide

Models: FH110D60F FLR085D36F FC085D36F FLF085D36F FLF110D48F FLR110D60F FLF110D60F FLR110D48F FH085D36F FH110D48F FLR140D60F

1 42

Download 42 pages 59.71 Kb

Page 11

Image 11

L

i

n e d

C h i m n e y

FIGURE 5

TYPICAL FLUE INSTALLATION REQUIREMENTS

FRONT FLUE LO-BOY MODEL SHOWN

(REPRESENTS ALL MODELS)

	Thimble	INSTALLER NOTE:
	Thimble
		Follow all appropriate
		standards for installing
		needed venting system.
		Draft Regulator
		(Be sure to follow
		installation inst.
	1/4 inch per	supplied with
	1/4 inch per	regulator).
	1 foot rise	regulator).
	1 foot rise
		90° Rotatable
		Flue Box on front
		flue models
		(remove appropriate
		cabinet knockout).
		Mounting screws
		located under flue
		box cover.
		Flue Box
		Cover

Optional

Flue

Locations

Oil Burner

Clean-out Door	Optional Fresh
(keep closed)	Air Boot (remove	MIS-1825
	rect. knockout).

Note: This accessory is not currently available for Bard Models: FH110D48F, FH110D60F, FLF110D48F, FLF110D60F with NX Burners

Manual	2100-422M
Page	11 of 42

Image 11

Bard FLR140D60F, FLR110D48F, FLR085D36F, FH110D60F, FLF085D36F, FLF110D48F, FLF110D60F, FLR110D60F, FH110D48F, FC085D36F I m n e y

Contents

OIL Furnace Installation Instructions Contents For More INFORMATION, Contact These Publishers Getting Other Information and Publications Minimum Clearances Equipment SelectionLocating the Furnace FLF/FLR 085, 110 and 140 Specification Sheet Supply Specification Sheet FC085 Model Dimensions Counterflow Specification Sheet Installation Installing the FurnaceInstalling a Cooling Unit Instruments Required for Proper Setup of the Furnace Electrical Data WiringFactory Wiring Field Wiring Typical Unit Setup FLF Unit Shown Typical Unit Setup FLF Unit Shown I m n e y Beckett AFG or NX OIL Burner Typical Single Inside Tank InstallationOIL Line Piping Genisys 7505 Primary Control Beckett Cleancut OIL PumpBeckett Solid State Igniter Burner States Reset Button OperationBeckett Genisys Table B Status Lights Table a Reset Button Operation Priming the Pump CAD Cell Resistance Indicator Disable Function Resetting from Restricted Lockout Electronic Blower Control Cleaner Connection Furnace Data Burner Setup and Adjustment Procedures Combustion Diagnosis Combustion Adjustment StepsPreparation Steps Short Form Adjustment Procedure Typical Smoke CO2 Chart with Adjustment Range High Air Settings Low Bacharach Smoke Number Pressure Gauge Connection to Bleed Port Correlation of Percent of CO2, O2 and Reserve AIR No Fuel OIL Efficiency Chart NET Stack TEMP. Degrees FRecommended START-UP Settings Spacing of Electrodes GUN Assembly AdjustmentRemoving GUN Assembly Combustion AIR Requirements Combustion AIR Boot Assembly AFG Burner Combustion AIR Boot Assembly ALL AIR from Inside Building Appliances Located in Confined Spaces Appliances Located in Confined Spaces ALL AIR from Outdoors Minimum Ventilation OpeningsALL Ventilation AIR from Outdoors Manual 2100-422M Vertical Venting Louvers and GrillesVenting Options Thermostat AFG AIR Filters Typical Installation of FR25 Filter KIT LO-BOY Models Filter Locations Filter Installation LO-BOY Models Final Inspection and Test Service HintsLubrication Inspect AIR Filter Removal of Burner only Combination Combustion CHAMBER/BURNER Mounting System Removal of Entire Combustion Chamber Mounting System To Remove Burner onlyTo Remove the Entire Combustion Chamber Mounting System Care of Finish Cleaning of the Heat ExchangerCommon Causes of Trouble Chart FLF/FLR085D36F Data Chart FH085D36F DataChart FH110D48F Data Chart FH110D60F Data Chart FC085D36F Data Chart FLR140D60F Data Exchanger FH Series Wiring Diagram 4047-119 E 4047-120 D