Plume Outlet Elbow | Baxi Potterton Gold HE A Range specification

Plume Outlet

Elbow

Fig. 34

Fig. 35

30mm

Fig. 36

200mm Min.

Fig. 37

9.0Plume Displacement

9.3General Fitting Notes (cont.)

15.For aesthetic purposes it is permissible to route the 60Ø exhaust in an enclosed box, but the air inlet and plume outlet MUST remain in free air.

16.It is also possible to separate the plume outlet from the 93° elbow to allow the flue to be installed as shown in Fig. 34.

17.To do this, first slacken the two screws retaining the

plume outlet to the elbow, and remove the outlet (Fig. 35). The elbow can now be used to connect the vertical to horizontal 60Ø exhaust (Fig. 34). Retighten the screws in the elbow.

18.The outlet can now be fitted into the female end of an 60Ø extension piece. It must be secured using two of the screws supplied in the bag with the ‘Jubilee’ clip.

19.Mark the female end of the extension at 30mm as shown in two positions, directly opposite each other (Fig. 36).

20.Using a suitable bit (e.g. 2mm), drill through the extension and outlet. Secure using two of the screws supplied.

21.The remaining screw must be used to secure the adaptor to the concentric terminal.

22.When the plume outlet is positioned under a balcony or other projection (Fig. 37) it must protrude at least 200mm (it is not necessary to extend it further than this).

23.When under balconies or projections it is permissible to rotate the concentric flue length up to 70°, clockwise or anti-clockwise (Fig. 38), if there is insufficient space to connect vertically.

24.This will allow the connection of the exhaust to the outlet spigot.

25.All other minimum & maximum dimensions must be adhered to, and the air inlet positioned such that it will not be subject to rain entry.

70°

	Concentric Flue Length
	(shown end-on)
	Outlet Spigot
	Fig. 38
© Baxi Heating UK Ltd 2008	27

Image 27

Baxi Potterton Gold HE A Range manual Plume Outlet Elbow

Contents

Installation & Service Instructions BS-EN ISO 9001 Accredited Company Natural Gas Scheme Members only Installer Notification Guidelines Important Installation, Commissioning, Service & Repair LegislationCodes of Practice refer to the most recent version Technique Safe Manual HandlingGeneral Preparation Contents Contents of Pack IntroductionDescription Layout General Layout Frost Protection Mode Appliance OperationPump Protection Gold Combi 24, 28 & 33 HE a Technical Data 22mm 15mm Dimensions and FixingsOrientation Flue Ø 100mm Tap Rail 32.5 mm Condensate Drain 65 mm Bypass System DetailsInformation Central Heating Circuit System Filling and Pressurising Fig Expansion Vessel Central Heating onlyPressure Relief Valve Fig Domestic Hot Water Circuit Fig ShowersHard Water Areas Site Requirements LocationClearances Figs Electrical Supply Site RequirementVentilation of Compartments Gas Supply Condensate Drain Flue terminal guard Flue This bend is equivalent to 1 metre Flue OptionsHorizontal Flues Horizontal Flue Systems Metre for each 135 bend This bend is equivalent to 1 metre Vertical Flues Twin PipeTwin & Vertical Flue Systems Metre for each 91.5 bend Flue Accessories Key Accessory Size Code No5111079 Flue Duct Adaptor Air duct adaptorFor Twin Flue Systems fit the adaptors as follows Flue Deflector Fig Flue DimensionsFor Roof Terminals Flue Trim Plume Displacement Plume Displacement Kit FigMetres Ring Adaptor Example Additional Accessories Elbow 5121369 Elbow Pair 512137028/33 Determining Permissible Lengths Exhaust, securing in the brackets Shown in . Complete the installation of the 60ØGeneral Fitting Notes 30mm Plume Outlet Elbow Installation Unpacking & Initial PreparationFlushing Hose Fitting Cold Inlet Stop Valve Loop and valves must be connected as shown in the diagram aFitting the Filling Loop Double Check Valve Stop Valve Temporary Filling Loop Tighten all the connections Fitting The BoilerFitting the Pressure Relief Discharge Pipe Fig Condensate Drain see section Ensure Elbow is fully Engaged into Boiler Fitting The FlueWall Thickness Waste Flue Elbow Inner Flue Support Bracket Ensure Flue is fully Engaged into Flue ElbowEnsure Extension is Fully engaged into Boiler Adaptor Cable Clamp Making The Electrical ConnectionsPreliminary Electrical Checks Terminal Block Cover Heat Exchanger Automatic Air Vent Screw Pump Selector Switch DisplayCommissioning Commissioning the Boiler Checking Temperature Control Setting the Timer Completion CompletionCase Front Panel Facia Panel 13 .1 Annual Servicing Servicing Annual Servicing BurnerViewing Window Changing Components Igniter FigSpark and Sensing Electrodes Fig Gasket Venturi Injector Cover Gas Inlet Pipe Fan Collector Fan FigVenturi Fig Injector Fig Burner Fig Insulation FigExtension Piece Flue/Heat Exchanger Thermostat Sensor Fig Central Heating Temperature Sensor NTC FigSafety Thermostat Fig DHW Temperature Sensor NTC Fig Automatic Air Vent Fig Heat Exchanger Automatic Air Vent FigPump Head Only Fig Pump Complete Fig Hall Effect Sensor Fig Pressure Gauge Figs Plate Heat Exchanger Fig Diverter Valve Motor Unit & Assembly Figs Pin Fig Selector Switch Fig14.20 P.C.B. Fig Completely undo the screws securing the control box Gas Valve Fig Expansion Vessel FigVenturi Inlet Pipe Temperature Control Selector Switch Display Combustion CheckChecking the CO2 Electrical Illustrated Wiring Diagram Short Parts List Short Parts ListKey Description Manufacturers Fault Finding Initial Fault Finding ChecksError Codes Pump runs Error 133 flashingReset position for 5 seconds Display illuminates Open DHW tap fully Error 110 flashingDomestic Hot Water Follow operational sequence Turn Domestic Hot Water Is there 230V at Main terminals L and N Main terminal fuse PCB X3 connector terminals 3Switch terminal Fan jammed or faulty winding Replace PCB Ensure that the Hall Effect Sensor is in position Gas at burnerReplace gas valve Terminals 1 Replace safety thermostat Replace PCB Is there 230V atReplace heat exchanger GAS Boiler Commissioning Checklist Service Interval Record UK Comp No 5116282 Iss 7 4/08 Brooks House, Coventry Road, Warwick. CV34 4LL