Setting the Timer | Baxi Potterton Gold HE A Range instruction

		10
Time Pointer		9
		9
		8
Constant
Timed		7
Timed
Off	0	AM
	0	5
		5
IN		4
	3

Rotate to adjust time

2	1	12
2		12
3		11
4		10
		9
PM		8
7		7
		7
8		AM
9		0
10		4
		4
11		3
12	1	2

On Position

12

Off Position

Fig. 71a

11

10

9

11.0Commissioning

11.3Setting the Timer

The Electro-Mechanical Timer allows the central heating system to be set every 15 minutes.

Using the three position switch the timer will allow either constant operation, timed operation or central heating off.

Move the switch button by sliding to the desired position.

Three position switch (Fig. 71a)

Constant (Top position): The heating will be on constantly irrespective of the position of the tappets.The heating will be controlled by the main thermostat on the appliance and/or any external controls.

Timed (Central position): The heating will operate

according to the position of the tappets and be controlled as above.

0Off (Bottom position): No central heating. Domestic hot water will operate on demand.

To set the time of day

Turn the timer outer bezel clockwise, to align the pointer with the correct time to the nearest 15 minutes ensuring that A.M./P.M. is considered. Do not at any time attempt to turn the bezel anti-clockwise.

To set the timed heating program

Decide which times of the day the central heating is required.

The heating will operate when the white tappets are set to the outer edge of the bezel.

To ensure the heating stays OFF set the required tappets inwards towards the centre of the bezel.

Each tappet represents 15 minutes.

For example: If the heating is not required between

10 A.M. and 11 A.M. the four tappets anticlockwise from the 10 A.M. will be set inwards (Fig. 71b).

Time Pointer

Fig. 71b

36© Baxi Heating UK Ltd 2008

Image 36

Baxi Potterton Gold HE A Range manual Setting the Timer

Contents

Installation & Service Instructions Natural Gas BS-EN ISO 9001 Accredited Company Installer Notification Guidelines Scheme Members only Important Installation, Commissioning, Service & Repair LegislationCodes of Practice refer to the most recent version Safe Manual Handling GeneralPreparation Technique Contents Contents of Pack IntroductionDescription General Layout Layout Frost Protection Mode Appliance OperationPump Protection Technical Data Gold Combi 24, 28 & 33 HE a Dimensions and Fixings OrientationFlue Ø 100mm Tap Rail 32.5 mm Condensate Drain 65 mm 22mm 15mm System Details InformationCentral Heating Circuit Bypass System Filling and Pressurising Fig Expansion Vessel Central Heating onlyPressure Relief Valve Fig Domestic Hot Water Circuit Fig ShowersHard Water Areas Site Requirements LocationClearances Figs Site Requirement Ventilation of CompartmentsGas Supply Electrical Supply Condensate Drain Flue Flue terminal guard Flue Options Horizontal FluesHorizontal Flue Systems This bend is equivalent to 1 metre Vertical Flues Twin Pipe Twin & Vertical Flue SystemsMetre for each 91.5 bend Metre for each 135 bend This bend is equivalent to 1 metre Flue Accessories Key Accessory Size Code No5111079 Flue Duct Adaptor Air duct adaptorFor Twin Flue Systems fit the adaptors as follows Flue Dimensions For Roof TerminalsFlue Trim Flue Deflector Fig Plume Displacement Plume Displacement Kit FigMetres Ring Adaptor Additional Accessories Elbow 5121369 Elbow Pair 5121370 28/33Determining Permissible Lengths Example Shown in . Complete the installation of the 60Ø General Fitting Notes30mm Exhaust, securing in the brackets Plume Outlet Elbow Installation Unpacking & Initial PreparationFlushing Loop and valves must be connected as shown in the diagram a Fitting the Filling LoopDouble Check Valve Stop Valve Temporary Filling Loop Hose Fitting Cold Inlet Stop Valve Fitting The Boiler Fitting the Pressure Relief Discharge Pipe FigCondensate Drain see section Tighten all the connections Fitting The Flue Wall Thickness WasteFlue Elbow Ensure Elbow is fully Engaged into Boiler Inner Flue Support Bracket Ensure Flue is fully Engaged into Flue ElbowEnsure Extension is Fully engaged into Boiler Adaptor Making The Electrical Connections Preliminary Electrical ChecksTerminal Block Cover Cable Clamp Selector Switch Display CommissioningCommissioning the Boiler Heat Exchanger Automatic Air Vent Screw Pump Temperature Control Checking Setting the Timer Completion CompletionCase Front Panel Facia Panel Servicing 13 .1 Annual Servicing Annual Servicing BurnerViewing Window Changing Components Igniter FigSpark and Sensing Electrodes Fig Fan Fig Venturi FigInjector Fig Gasket Venturi Injector Cover Gas Inlet Pipe Fan Collector Burner Fig Insulation FigExtension Piece Central Heating Temperature Sensor NTC Fig Safety Thermostat FigDHW Temperature Sensor NTC Fig Flue/Heat Exchanger Thermostat Sensor Fig Heat Exchanger Automatic Air Vent Fig Pump Head Only FigPump Complete Fig Automatic Air Vent Fig Pressure Gauge Figs Hall Effect Sensor Fig Diverter Valve Motor Unit & Assembly Figs Plate Heat Exchanger Fig Selector Switch Fig 14.20 P.C.B. FigCompletely undo the screws securing the control box Pin Fig Gas Valve Fig Expansion Vessel FigVenturi Inlet Pipe Temperature Control Selector Switch Display Combustion CheckChecking the CO2 Illustrated Wiring Diagram Electrical Short Parts List Short Parts ListKey Description Manufacturers Fault Finding Initial Fault Finding ChecksError Codes Error 133 flashing Reset position for 5 secondsDisplay illuminates Pump runs Error 110 flashing Domestic Hot Water Follow operational sequenceTurn Domestic Hot Water Open DHW tap fully PCB X3 connector terminals 3 Switch terminalFan jammed or faulty winding Replace PCB Is there 230V at Main terminals L and N Main terminal fuse Gas at burner Replace gas valveTerminals 1 Ensure that the Hall Effect Sensor is in position Replace safety thermostat Replace PCB Is there 230V atReplace heat exchanger GAS Boiler Commissioning Checklist Service Interval Record Brooks House, Coventry Road, Warwick. CV34 4LL UK Comp No 5116282 Iss 7 4/08