Controls and functions, Projector | BenQ mw814st manual

Controls and functions

Projector

1

		6
		7
	2	8
	3	9
	4	10
	4	11
		11
	5	12
	5	13
		13
		8

1.Focus ring

Adjusts the focus of the projected image.

2.LAMP indicator light

Indicates the status of the lamp. Lights up or flashes when the lamp has developed a problem.

3.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

4. Left/

Decreases the projector volume.

5.BLANK

Used to hide the screen picture.

6.TEMPerature warning light

Lights up red if the projector's temperature becomes too high.

7.POWER indicator light

Lights up or flashes when the projector is under operation.

8.Keystone/Arrow keys ( / Up, /

Down)

Manually corrects distorted images resulting from an angled projection.

9.Auto

Automatically determines the best picture timings for the displayed image.

10. Right/

Increases the projector volume.

When the On-Screen Display (OSD) menu is activated, the #4, #8, and #10 keys are used as directional arrows to select the desired menu items and to make adjustments.

11. POWER

Toggles the projector between standby mode and on.

12.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

13.SOURCE

Displays the source selection bar.

10 Introduction

Image 10

BenQ mw814st user manual Controls and functions, Projector

Contents

Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructions Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearance Serviced InstalledIt from the power supplys power outlet Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions Projector Remote control Replacing the remote control battery Remote control effective rangePull out the battery holder Front Table Positioning your projectorChoosing a location Front Ceiling Diagonal Height Width From screen Offset Inches 2032 Projection dimensionsObtaining a preferred projected image size 996 1771 866 B1 a 120 3048 1615 2585 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787100 2540 1346 2154 150 3810 2019 3231 Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Best Starting up the projector OperationOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarity Correcting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTER Entering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projected Count Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection Description Hiding the image Remote paging operationsFreezing the image Locking control keys Operating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen Controlling the projector through a LAN environment Adjusting the soundCable connection Controlling the projector remotely through a web browser If you are in a non-DHCP environment Iiii Iiiv Press Exit to go back to the remote network operation Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Management Save Settings Picture ModeTemperature 3D Color Display menu Picture menu Function Description Teaching Search TimerSettings Color Space Panel Key Function DescriptionOperation Lock Audio System Setup Advanced menu Function Description HighAltitude Lamp Standby System Setup Advanced menu Function DescriptionReset All Network System Information menu Function DescriptionCurrent Status Maintenance Care of the projector Lamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Wall mount installation Minimum installation requirements Ceiling Minimum Ceiling Height mm = f + H + b + 60 + 274+ cWall plate Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Horizontal Copyright Warranty and Copyright informationLimited warranty Disclaimer