Adjusting the sound, Cable connection | BenQ mw814st manual

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speaker. Be sure you have made a correct connection to the projector audio input. See "Connection" on page 17 for how the audio input is connected.

Muting the sound

To temporarily turn off the sound:

1.Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.Press to highlight Audio Settings and press MODE/ENTER. The Audio Settings page displays.

3.Highlight Mute and press / to select On.

Adjusting the sound level

To adjust the sound level, press VOLUME+/VOLUME- or / , or:

1.Repeat steps 1-2above.

2.Press to highlight Volume and press / to select a desired sound level.

Turning off the Power On/Off Ring Tone

To turn off the ring tone:

1.Repeat steps 1-2above.

2.Press to highlight Power On/Off Ring Tone and press / to select Off.

The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power On/Off Ring Tone.

Controlling the projector through a LAN environment

You can manage and control the projector from a remote computer when they are properly connected to the same local area network.

Cable connection

If you are in a DHCP environment:

1.Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port on your Ethernet or router.

Operation 35

Image 35

BenQ mw814st user manual Adjusting the sound, Controlling the projector through a LAN environment, Cable connection

Contents

Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higher Do not step on the projector or place InstalledIt from the power supplys power outlet Serviced Introduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewFront/upper side Projector Controls and functions Remote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Front Ceiling Positioning your projectorChoosing a location Front Table 996 1771 866 Projection dimensionsObtaining a preferred projected image size Diagonal Height Width From screen Offset Inches 2032 B1 a 150 3810 2019 3231 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787100 2540 1346 2154 120 3048 1615 2585 Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearance Operation OperationStarting up the projector Fine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Correcting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a password Write down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details Screen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 mode Fine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color Management Selection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count Down Locking control keys Remote paging operationsFreezing the image Hiding the image Creating your own startup screen To activate the High Altitude ModeOperating in a high altitude environment Cable connection Adjusting the soundControlling the projector through a LAN environment If you are in a non-DHCP environment Controlling the projector remotely through a web browser Iiii Iiiv Press Exit to go back to the remote network operation Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature 3D Color Management Save Settings Color Space TimerSettings Search Lock Function DescriptionOperation Panel Key Lamp System Setup Advanced menu Function Description HighAltitude Audio Network System Setup Advanced menu Function DescriptionReset All Standby Status Information menu Function DescriptionCurrent System Care of the projector Maintenance Getting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp information Status Message Timing of replacing the lamp Replacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector Maintenance Resetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp events Troubleshooting Projector specifications Specifications Ceiling mount installation Dimensions Minimum installation requirements Wall mount installation Wall plate Minimum Ceiling Height mm = f + H + b + 60 + 274+ cCeiling Supported timing for PC input Timing chart Supported timing for Hdmi Hdcp input Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Timing Disclaimer Warranty and Copyright informationLimited warranty Copyright