Table of contents | BenQ mw814st specification

Table of contents
Important safety
instructions	3
Introduction	7
Projector features	7
Shipping contents	8
Projector exterior view	9
Controls and functions	10

Positioning your projector13

Choosing a location	13
Obtaining a preferred projected
image size	14
Connection	17
Connecting video source devices	18
Operation	19
Starting up the projector	19
Adjusting the projected image	20
Using the menus	22
Securing the projector	23
Switching input signal	26
Magnifying and searching for details . 27
Selecting the aspect ratio	27
Optimizing the image	29
Setting the presentation timer	32
Remote paging operations	33
Freezing the image	33
Hiding the image	33
Locking control keys	33
Operating in a high altitude
environment	34
Creating your own startup screen	34
Adjusting the sound	35

Controlling the projector through a LAN
environment	35
Shutting down the projector	39
Direct power off	39
Menu operation	40
Maintenance	50
Care of the projector	50
Lamp information	51
Troubleshooting	57
Specifications	58
Projector specifications	58
Dimensions	59
Ceiling mount installation	59
Wall mount installation	60
Timing chart	62
Warranty and Copyright
information	65

2 Table of contents

Image 2

BenQ mw814st user manual Table of contents

Contents

Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructions Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearance Serviced InstalledIt from the power supplys power outlet Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Projector Remote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Front Table Positioning your projectorChoosing a location Front Ceiling Diagonal Height Width From screen Offset Inches 2032 Projection dimensionsObtaining a preferred projected image size 996 1771 866 B1 a 120 3048 1615 2585 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787100 2540 1346 2154 150 3810 2019 3231 Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Best Operation OperationStarting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarity Correcting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTER Write down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projected Count Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection Description Hiding the image Remote paging operationsFreezing the image Locking control keys Creating your own startup screen To activate the High Altitude ModeOperating in a high altitude environment Cable connection Adjusting the soundControlling the projector through a LAN environment Controlling the projector remotely through a web browser If you are in a non-DHCP environment Iiii Iiiv Press Exit to go back to the remote network operation Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Management Save Settings Picture ModeTemperature 3D Color Display menu Picture menu Function Description Teaching Search TimerSettings Color Space Panel Key Function DescriptionOperation Lock Audio System Setup Advanced menu Function Description HighAltitude Lamp Standby System Setup Advanced menu Function DescriptionReset All Network System Information menu Function DescriptionCurrent Status Maintenance Care of the projector Lamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Wall mount installation Minimum installation requirements Wall plate Minimum Ceiling Height mm = f + H + b + 60 + 274+ cCeiling Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Horizontal Copyright Warranty and Copyright informationLimited warranty Disclaimer