Manuals / BenQ / Computer Equipment / Projector

BenQ mw814st user manual Connection

Models: mw814st

1 65

Download 65 pages 60.8 Kb

Page 17

Connection

Connection

When connecting a signal source to the projector, be sure to:

1.Turn all equipment off before making any connections.

2.Use the correct signal cables for each source.

3.Ensure the cables are firmly inserted.

•In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 8). They are commercially available from electronics stores.

•The connection illustrations below are for reference only. The rear connecting jacks available on the projector vary with each projector model.

Notebook or desktop computer

Monitor

A/V device

	(VGA)		(DVI)
		2	3							7	8	Speakers	9

	1			1	9	4	5	9	6
	1			1	9	4	5	9	6

or

or

1.VGA cable

2.VGA to DVI-A cable

3.USB cable

4.HDMI cable

5.Component Video to VGA (D-Sub) adapter cable

6.Audio L/R cable

7.S-Video cable

8.Video cable

9.Audio cable

Connection 17

Image 17

BenQ mw814st user manual Connection

Contents

Welcome MW814ST Digital Projector User ManualImportant safety Table of contentsWarranty and Copyright MaintenanceSafety Instructions Important safety instructionsSafety Instructions Continued Always place the projector on a level Ceiling mounting the projector Introduction Projector featuresOptional accessories Shipping contentsStandard accessories Rear/lower side Projector exterior viewFront/upper side Projector Controls and functionsRemote control Replacing the remote control battery Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Projection dimensionsB1 a Table B2 The screen aspect ratio is 43 and the projected picture is Connection Connecting audio Connecting video source devicesStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Using the menus Utilizing the password function Using a security cable lockSetting a password Securing the projectorEntering the password recall procedure If you forget the password2. Write down the number and turn off your projector 24 Operation2. Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAuto Scales an image proportionally to fit About the aspect ratio169 Scales an image so that it is horizontal or vertical width. This is suitableSelecting a picture mode Using Wall ColorOptimizing the image Adjusting Brightness Fine-tuning the image quality in user modesAdjusting Contrast Adjusting Colorvalues to your preference by pressing 3D Color ManagementTo cancel the timer, perform the following steps Setting the presentation timerFreezing the image Remote paging operationsHiding the image Locking control keysTo activate the High Altitude Mode Operating in a high altitude environmentCreating your own startup screen Cable connection Adjusting the soundControlling the projector through a LAN environment If you are in a non-DHCP environment Controlling the projector remotely through a web browserThe Menu button can also be used to go back to previous OSD menu, exit and save menu settings Press Exit to go back to the remote network operation page iv. Once set, access to the tools page has been password-protected38 Operation Shutting down the projector Direct power offMenu system Menu operationMain menu SETUPSub-menu OptionsChange Password Reset Lamp Timer42 Operation INFORMATIONsearching for details on page 27 for details Description of each menuwhite. See Using Wall Color on page 29 for details image. See Adjusting Color on page 30 for details See Adjusting Contrast on page 30 for detailsSee Adjusting Brilliant Color on page 30 for details Adjusts the degree of difference between dark and light in the imageframe. See Setting the presentation timer on page 32 for details See Switching input signal on page 26 for detailsSets the language for the On-Screen Display OSD menus. See Using See Changing Color Space on page 26 for detailsEnables or disables the Quick Cooling function. Selecting On enables POWER key on the projector when the projector is in standby modeyour own startup screen on page 34 for details Captures and stores the projected picture as My Screen. See CreatingSee Setting Lamp Mode as Economic on page 51 for details See Adjusting the sound on page 35 for detailsSee Resetting the lamp timer on page 55 for details one. See Utilizing the password function on page 23 for detailsSecurity Settings, Network Settings and Baud Rate Enabling this function slightly increases the standby poweronly be fed into the AUDIO-IN L/R jacks. There is no need to connect consumptionFunction 6. INFORMATION menuDescription CurrentCleaning the lens MaintenanceCleaning the projector case Care of the projectorExtending lamp life Lamp informationGetting to know the lamp hour Install a new lamp for optimal performance. If the Timing of replacing the lampprojector is normally run with Economic selected whenever you notice that the brightness level hasReplacing the lamp 7. Use the handle to slowly pull the lamp out of the projector Do not turn the power on with the lamp cover removed Resetting the lamp timerPower events IndicatorsLight Status & Descriptionprocedure on page 24 for details TroubleshootingPlease see Entering the password recall Projector specifications SpecificationsCeiling mount installation DimensionsSpecifications 287.3 mm W x 114.4 mm H x 232.6 mm DMinimum installation requirements Wall mount installationMinimum Ceiling Height mm = f + H + b + 60 + 274+ c Supported timing for PC input Timing chartSupported timing for HDMI HDCP input 64 Specifications Supported timing for Component-YPbPr inputSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright Disclaimer