Advanced | BenQ MX613ST, MS612ST instruction

	Main menu Sub-menu			Options

		Quick Cooling		On/Off
		High Altitude Mode		On/Off
			Mute	On/Off
		Audio Settings	Volume
		Audio Settings	Power On/Off	On/Off
			Power On/Off
			Ring Tone
			Ring Tone
		Lamp Settings	Lamp Mode	Normal/Economic
		Lamp Settings	Reset Lamp Timer
			Equivalent Lamp Hour
		Security	Change Password
	5.	Security	Change Security	Power On Lock
		Settings	Change Security	Power On Lock
		Settings	Settings	Splash Screen Lock
	SYSTEM		Settings	Splash Screen Lock
	SYSTEM			2400/4800/9600/14400/19200/
	SETUP:	Baud Rate		2400/4800/9600/14400/19200/
	SETUP:	Baud Rate		38400/57600/115200
	Advanced			38400/57600/115200
	Advanced	Test Pattern		On/Off
			Closed Caption	On/Off
		Closed Caption	Enable	On/Off
		Closed Caption	Enable
			Caption Version	CC1/CC2/CC3/CC4
		Standby	Network	On/Off
		Settings	Monitor Out	On/Off
			Status
		Wireless LAN	SSID
		Wireless LAN	IP Address
			IP Address
			Connection Mode
		Reset All Settings
		FAQ-Image and Installation
		FAQ-Features and Service

6.		•	Source
6.		•	Picture Mode
INFORMATION	Current System Status	•	Resolution
	Current System Status	•	Color System
		•	Color System
		•	Equivalent Lamp Hour
		•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

46 Operation

Image 46

BenQ MX613ST, MS612ST user manual Advanced

Contents

Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructions Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearance Serviced InstalledIt from the power supplys power outlet Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Timer Set up Volume +Timer On Freeze Pull out the battery holder Remote control effective rangeReplacing the remote control battery Approx.+15º Front Table Positioning your projectorChoosing a location Front Ceiling Screen size Distance from screen mm Diagonal Projection dimensionsObtaining a preferred projected image size Vertical Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Best Starting up the projector OperationOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTER Entering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projected Count Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection Description Freezing the image Utilizing FAQ functionRemote paging operations Hiding the image Locking control keys On the remote control or projector forTo activate the High Altitude Mode Operating in a high altitude environment Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Muting the sound Wireless connection Controlling the projector through a LAN environmentPage Page Page Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description 3D Sync Settings System Setup Basic menu Function Description Quick AutoTimer Search Lock Panel KeyBackground Splash Reset All System Setup Advanced menu Function DescriptionWireless Baud Rate System Features ServiceCurrent Status Maintenance Care of the projector Lamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Ceiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Unit mm Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Horizontal Copyright Warranty and Copyright informationLimited warranty Disclaimer EEC statement for European users Regulation statementsFCC statement for United States users Weee directive