Search, Color Space, Conversion, Presentation, Timer | BenQ MS612ST

3. SOURCE menu

4. SYSTEM SETUP: Basic menu

	Function	Description
	Quick Auto	See "Switching input signal" on page 24 for details.
	Search	See "Switching input signal" on page 24 for details.
	Search

	Color Space	See "Changing Color Space" on page 24 for details.
	Conversion	See "Changing Color Space" on page 24 for details.
	Conversion
	Presentation	Reminds the presenter to finish the presentation within a certain time
	Timer	frame. See "Setting the presentation timer" on page 30 for details.

	Language	Sets the language for the On-Screen Display (OSD) menus. See "Using
	Language	the menus" on page 20 for details.
		the menus" on page 20 for details.

	Projector	The projector can be installed on a ceiling or behind a screen, or with
	Position	one or more mirrors. See "Choosing a location" on page 13 for details.

		Menu Display Time
		Sets the length of time the OSD will remain active after your last key
	Menu	press. The range is from 5 to 30 seconds in 5-second increments.
	Menu	Menu Position
	Settings	Menu Position
	Settings	Sets the On-Screen Display (OSD) menu position.
		Reminder Message
		Sets the reminder messages on or off.

		Direct Power On
		Allows the projector to turn on automatically once the power is fed
		through the power cord.
		Auto Power Off
		Allows the projector to turn off automatically if no input signal is
		detected after a set period of time. See "Setting Auto Power Off" on page
	Operation	54 for details.
	Settings	Blank Timer
		Sets the image blank time when the Blank feature is activated, once
		elapsed the image will return to the screen. See "Hiding the image" on
		page 31 for details.
		Sleep Timer
		Sets the auto-shutdown timer. The timer can be set to a value between
		30 minutes and 12 hours.

	Remote	Allows you to enable all the remote receivers or one specific remote
	Receiver	receiver on the projector.

Operation 49

Image 49

BenQ MS612ST System Setup Basic menu Function Description Quick Auto, Search, Color Space, Conversion, Presentation, Timer

Contents

Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructions Safety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearance It from the power supplys power outlet InstalledServiced Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Timer On Volume +Timer Set up Freeze Replacing the remote control battery Remote control effective rangePull out the battery holder Approx.+15º Choosing a location Positioning your projectorFront Table Front Ceiling Obtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal Vertical Connection Connecting audio Connecting video source devicesTerminal name Terminal appearance Best Starting up the projector OperationOperation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTER Entering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details Adjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Range at 0, only pure red in the projected To cancel the timer, perform the following steps Setting the presentation timerCount Up Increases from 0 to the preset time Count Down Selection Description Remote paging operations Utilizing FAQ functionFreezing the image Hiding the image To activate the High Altitude Mode On the remote control or projector forLocking control keys Operating in a high altitude environment Adjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the sound Controlling the projector through a LAN environment Wireless connectionPage Page Page Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu Function Description 3D Sync Timer System Setup Basic menu Function Description Quick AutoSettings Search Background Panel KeyLock Splash Wireless System Setup Advanced menu Function DescriptionReset All Baud Rate Current Features ServiceSystem Status Care of the projector Maintenance Setting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hour Status Message Timing of replacing the lamp Replacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector Maintenance Resetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal events Troubleshooting Projector specifications Specifications Mm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mm Supported timing for PC input Timing chart Supported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Horizontal Limited warranty Warranty and Copyright informationCopyright Disclaimer FCC statement for United States users Regulation statementsEEC statement for European users Weee directive