Remote control effective range, Approx.+15º | BenQ MX613ST, MS612ST

Remote control effective range

Infra-Red (IR) remote control sensors are located on the front and the top of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensors to function correctly. The distance between the remote control and the sensors should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensors on the projector that might obstruct the infra-red beam.

• Operating the projector from the front • Operating the projector from the top

Capture

Approx.+15º

Capture

	º
ox.	+15
Appr

Replacing the remote control battery

1.Pull out the battery holder.

Please follow the illustrated instructions. Push and hold the locking arm while pulling out the battery holder.

2. Insert the new battery in the holder. Note the positive polarity should face outward.

3.Push the holder into the remote control.

• Avoid excessive heat and humidity.

• There may be battery damage if the battery is incorrectly replaced.

• Replace only with the same or equivalent type recommended by the battery manufacturer.

•Dispose of the used battery according to the battery

manufacturer's instructions.

•Never throw a battery into a fire. There may be danger of an explosion.

•If the battery is dead or if you will not be using the remote control for a long time, remove the battery to prevent damage to the remote control from possible battery leakage.

12 Introduction

Image 12

BenQ MX613ST, MS612ST user manual Remote control effective range, Replacing the remote control battery, Approx.+15º

Contents

Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructions Safety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearance Installed It from the power supplys power outletServiced Do not step on the projector or place Projector features IntroductionIntroduction Shipping contents Projector exterior view Projector Volume + Timer OnTimer Set up Freeze Remote control effective range Replacing the remote control batteryPull out the battery holder Approx.+15º Positioning your projector Choosing a locationFront Table Front Ceiling Projection dimensions Obtaining a preferred projected image sizeScreen size Distance from screen mm Diagonal Vertical Connection Connecting video source devices Connecting audioTerminal name Terminal appearance Best Operation Starting up the projectorOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTER If you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio Projectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projected Setting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection Description Utilizing FAQ function Remote paging operationsFreezing the image Hiding the image On the remote control or projector for To activate the High Altitude ModeLocking control keys Operating in a high altitude environment Adjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Muting the sound Wireless connection Controlling the projector through a LAN environmentPage Page Page Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu Function Description 3D Sync System Setup Basic menu Function Description Quick Auto TimerSettings Search Panel Key BackgroundLock Splash System Setup Advanced menu Function Description WirelessReset All Baud Rate Features Service CurrentSystem Status Maintenance Care of the projector Setting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal events Troubleshooting Specifications Projector specifications Dimensions Mm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25Ceiling Mount screw M4 x 8 Max L = 8 mm Unit mm Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Horizontal Warranty and Copyright information Limited warrantyCopyright Disclaimer Regulation statements FCC statement for United States usersEEC statement for European users Weee directive