Table of contents | BenQ MX613ST, MS612ST specification

Table of contents
Important safety
instructions	3
Introduction	7
Projector features	7
Shipping contents	8
Projector exterior view	9
Controls and functions	10
Positioning your
projector	13
Choosing a location	13
Obtaining a preferred projected
image size	14
Connection	15
Connecting video source devices	16
Operation	17
Starting up the projector	17
Adjusting the projected image	18
Using the menus	20
Securing the projector	21
Switching input signal	24
Magnifying and searching for details . 25
Selecting the aspect ratio	25
Optimizing the image	27
Setting the presentation timer	30
Remote paging operations	31
Freezing the image	31
Hiding the image	31
Utilizing FAQ function	31
Locking control keys	32
Operating in a high altitude
environment	32
Creating your own startup screen	32

Adjusting the sound	33
Controlling the projector through
a LAN environment	34
Presenting from a USB Reader	42
Shutting down the projector	43
Direct power off	43
Menu operation	44
Maintenance	53
Care of the projector	53
Lamp information	54
Troubleshooting	60
Specifications	61
Projector specifications	61
Dimensions	62
Ceiling mount installation	62
Timing chart	63
Warranty and Copyright
information	66
Regulation statements	67

2 Table of contents

Image 2

BenQ MX613ST, MS612ST user manual Table of contents

Contents

Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructions Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearance Serviced InstalledIt from the power supplys power outlet Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Timer Set up Volume +Timer On Freeze Pull out the battery holder Remote control effective rangeReplacing the remote control battery Approx.+15º Front Table Positioning your projectorChoosing a location Front Ceiling Screen size Distance from screen mm Diagonal Projection dimensionsObtaining a preferred projected image size Vertical Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Best Operation OperationStarting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTER Write down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projected Count Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection Description Freezing the image Utilizing FAQ functionRemote paging operations Hiding the image Locking control keys On the remote control or projector forTo activate the High Altitude Mode Operating in a high altitude environment Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Muting the sound Wireless connection Controlling the projector through a LAN environmentPage Page Page Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Page Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description 3D Sync Settings System Setup Basic menu Function Description Quick AutoTimer Search Lock Panel KeyBackground Splash Reset All System Setup Advanced menu Function DescriptionWireless Baud Rate System Features ServiceCurrent Status Maintenance Care of the projector Lamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Ceiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Unit mm Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Horizontal Copyright Warranty and Copyright informationLimited warranty Disclaimer EEC statement for European users Regulation statementsFCC statement for United States users Weee directive