Indicators, Light Status & Description Power events | BenQ MS612ST

Indicators

Light

Status & Description

					Power events

	Orange	Off	Off	Stand-by mode.
	Green	Off	Off	Powering up.
	Flashing	Off	Off	Powering up.
	Flashing
	Green	Off	Off	Normal operation.
				• The projector needs 90 seconds to cool down as it was
					abnormally shut down without the normal cooling down
					process.
	Orange	Off	Off	• The projector needs to cool for 90 seconds after the power
	Flashing	Off	Off		is turned off.
	Flashing				is turned off.
				• The projector has shut down automatically. If you try to re-
					start the projector, it will shut down again. Please contact
					your dealer for assistance.

					Lamp events
	Orange	Off	Red	The projector has shut down automatically. If you try to re-
	Orange			start the projector, it will shut down again. Please contact your
	Flashing
	Flashing			dealer for assistance.
				dealer for assistance.

	Off	Off	Red	1.	The projector needs 90 seconds to cool down. Or
	Off	Off	Red	2.	Please contact your dealer for assistance.
				2.	Please contact your dealer for assistance.

Thermal events

Off	Red	Off
Off	Red	Red
Off	Red	Green
Off	Red	Orange
Red	Red	Red
Red	Red	Green
Red	Red	Orange
Green	Red	Red
Green	Red	Green
Green	Red	Orange
Orange	Red	Red
Orange	Red	Green
Orange	Red	Orange
Off	Green	Red
Off	Green	Green

The projector has shut down automatically. If you try to re- start the projector, it will shut down again. Please contact your dealer for assistance.

Maintenance 59

Image 59

BenQ MS612ST, MX613ST user manual Indicators, Light Status & Description Power events, Lamp events, Thermal events

Contents

Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higher Do not step on the projector or place InstalledIt from the power supplys power outlet Serviced Introduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Freeze Volume +Timer On Timer Set up Approx.+15º Remote control effective rangeReplacing the remote control battery Pull out the battery holder Front Ceiling Positioning your projectorChoosing a location Front Table Vertical Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm Diagonal Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearance Operation OperationStarting up the projector Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Correcting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a password Write down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details Screen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 mode Fine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color Management Selection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count Down Hiding the image Utilizing FAQ functionRemote paging operations Freezing the image Operating in a high altitude environment On the remote control or projector forTo activate the High Altitude Mode Locking control keys Muting the sound Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring Tone Controlling the projector through a LAN environment Wireless connectionPage Page Page Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Page Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Display menu Picture menu Function Description 3D Sync Picture ModeTemperature Save Settings Search System Setup Basic menu Function Description Quick AutoTimer Settings Splash Panel KeyBackground Lock Baud Rate System Setup Advanced menu Function DescriptionWireless Reset All Status Features ServiceCurrent System Care of the projector Maintenance Getting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp information Status Message Timing of replacing the lamp Replacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector Maintenance Resetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp events Troubleshooting Projector specifications Specifications Unit mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Ceiling Mount screw M4 x 8 Max L = 8 mm Supported timing for PC input Timing chart Supported timing for Hdmi Hdcp input Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Timing Disclaimer Warranty and Copyright informationLimited warranty Copyright Weee directive Regulation statementsFCC statement for United States users EEC statement for European users