Panel Key, Background, Lock, Splash, Screen, Quick | BenQ MX613ST

		Function
		Panel Key
	4.	Panel Key
	SYSTEM	Background
		Lock
	SETUP:	Color
	SETUP:	Splash
		Splash
	Basic	Screen
	Basic
	menu	My Screen
		My Screen
		Quick
		Cooling
		High
	5.	Altitude
	5.	Mode
	SYSTEM	Mode
	SYSTEM	Settings
		Audio
	SETUP:	Lamp
	Advancedmenu	Lamp
	Advancedmenu	Settings
		Settings
		Security
		Settings

Description

Disables or enables all panel key functions except POWER on the projector and keys on the remote control. See "Locking control keys" on page 32 for details.

Sets the background color for the projector.

Allows you to select which logo screen will display during projector start-up. The following options are available: BenQ logo, My Screen, Black screen, Blue screen.

Captures and stores the projected picture as My Screen. See "Creating your own startup screen" on page 32 for details.

In the unlikely event that the capturing action fails, change your target picture.

Enables or disables the Quick Cooling function. Selecting On enables the function and projector cooling time will be shortened from a normal 90-second duration to approximately 30 seconds.

A mode for operation in high altitude areas. See "Operating in a high altitude environment" on page 32 for details.

Mute

Volume

Power On/Off Ring Tone

See "Adjusting the sound" on page 33 for details.

Lamp Mode

See "Setting Lamp Mode as Economic" on page 54 for details.

Reset Lamp Timer

See "Resetting the lamp timer" on page 58 for details.

Equivalent Lamp Hour

See "Getting to know the lamp hour" on page 54 for details on how the total lamp hour is calculated.

Change Password

You will be asked to enter the current password before changing to a new one. See "Utilizing the password function" on page 21 for details.

Change Security Settings

Power On Lock

Splash Screen Lock

See "Utilizing the password function" on page 21 for details.

50 Operation

Image 50

BenQ MX613ST Panel Key, Background, Lock, Splash, My Screen, Quick, Cooling, High, Altitude, Audio, Lamp, Security

Contents

Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructions Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearance Serviced InstalledIt from the power supplys power outlet Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Timer Set up Volume +Timer On Freeze Pull out the battery holder Remote control effective rangeReplacing the remote control battery Approx.+15º Front Table Positioning your projectorChoosing a location Front Ceiling Screen size Distance from screen mm Diagonal Projection dimensionsObtaining a preferred projected image size Vertical Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Best Operation OperationStarting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTER Write down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projected Count Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection Description Freezing the image Utilizing FAQ functionRemote paging operations Hiding the image Locking control keys On the remote control or projector forTo activate the High Altitude Mode Operating in a high altitude environment Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Muting the sound Wireless connection Controlling the projector through a LAN environmentPage Page Page Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Page Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description 3D Sync Settings System Setup Basic menu Function Description Quick AutoTimer Search Lock Panel KeyBackground Splash Reset All System Setup Advanced menu Function DescriptionWireless Baud Rate System Features ServiceCurrent Status Maintenance Care of the projector Lamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Ceiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Unit mm Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Horizontal Copyright Warranty and Copyright informationLimited warranty Disclaimer EEC statement for European users Regulation statementsFCC statement for United States users Weee directive