Advanced Network

Main menu Sub-menu			Options

		Closed Caption	On/Off
	Closed Caption Enable		On/Off
	Closed Caption Enable
		Caption Version	CC1/CC2/CC3/CC4
	Standby	Network	On/Off
	Standby	Microphone	On/Off
	Settings	Microphone	On/Off
	Settings	Monitor Out	On/Off
		Monitor Out	On/Off
			Status
			DHCP
5.			IP Address
5.		Wired LAN	Subnet Mask
SYSTEM		Wired LAN	Subnet Mask
SYSTEM			Default Gateway
SETUP:			Default Gateway
SETUP:			DNS Server
Advanced Network			DNS Server
Advanced Network			Apply
	Settings		Status
		Wireless LAN	SSID
		Wireless LAN	IP Address
			IP Address
			Connection Mode
			Account
		Remote Desktop	Password
			Connect
	Reset All Settings
	FAQ-Image and Installation
	FAQ-Features and Service

6.		•	Source
6.		•	Picture Mode
INFORMATION	Current System Status	•	Resolution
	Current System Status	•	Color System
		•	Color System
		•	Equivalent Lamp Hour
		•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Operation 55

Page 55

Image 55

Contents

MX760/MX761 Digital Projector Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higher Do not step on the projector or place InstalledIt from the power supplys power outlet Serviced Introduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior view Left Power indicator lightFocus ring Zoom ring Keystone/Arrow buttons / Up Down Remote controlTest Auto Numeric buttons Operating the Laser pointerMute MIC/VOL + Replacing the remote control batteries Remote control effective rangeApprox.+15º Front Ceiling Positioning your projectorChoosing a location Front Table Obtaining a preferred projected image size Projection dimensions Shifting the projection lens When the projector position is fixed Video cable Hdmi cable Connection Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearance About the microphone input Playing sound through the projectorDevice Page Starting up the projector OperationOperation Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Correcting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a password Write down the number and turn off your projector If you forget the passwordEntering the password recall procedure Changing the password Disabling the password function Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details Screen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 mode Fine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color Management Selection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count Down Hiding the image Utilizing FAQ functionRemote paging operations Freezing the image Operating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keys Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volume If you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environment Highlight Wireless LAN and press MODE/ENTER Wireless connection Controlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Basic Menu operationMenu system Main menu Sub-menu Options Advanced Advanced Network Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save Settings Search System Setup Basic menu Function Description Quick AutoTimer Settings Lock Settings Security DescriptionPanel Key Background Test Pattern System Setup Advanced menu Function DescriptionReset All Baud Rate Status Features ServiceCurrent System Care of the projector Maintenance Getting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp information Status Message Timing of replacing the lamp Replacing the lamp Tighten the screw that secures the lamp Resetting the lamp timer Connect the power and restart the projectorTighten the screw that secures the lamp cover Thermal events IndicatorsLight Status & Description Power events Lamp events Troubleshooting Projector specifications Specifications Unit mm DimensionsMm W x 128 mm H x 252 mm D Ceiling Mount screw M4 x 8 Max L = 8 mm Supported timing for PC input Timing chart Supported timing for Hdmi Hdcp input Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Timing Disclaimer Warranty and Copyright informationLimited warranty Copyright Weee directive Regulation statementsFCC statement for United States users EEC statement for European users

BenQ MX761 user manual Advanced Network

Models: MX761

Main menu Sub-menu

SETUP:

SSID

Operation 55