Manuals / BenQ / Computer Equipment / Projector

BenQ MX761 System Setup Basic menu Function Description Quick Auto, Search, Color Space, Timer

Models: MX761

1 77

Download 77 pages 48.55 Kb

Page 58

3. SOURCE menu

4. SYSTEM SETUP: Basic menu

	Function	Description
	Quick Auto	See "Switching input signal" on page 28 for details.
	Search	See "Switching input signal" on page 28 for details.
	Search

	Color Space	See "Changing Color Space" on page 28 for details.
	Conversion	See "Changing Color Space" on page 28 for details.
	Conversion
	Presentation	Reminds the presenter to finish the presentation within a certain time
	Timer	frame. See "Setting the presentation timer" on page 34 for details.

	Language	Sets the language for the On-Screen Display (OSD) menus. See "Using
	Language	the menus" on page 24 for details.
		the menus" on page 24 for details.

	Projector	The projector can be installed on a ceiling or behind a screen, or with
	Position	one or more mirrors. See "Choosing a location" on page 14 for details.

		Menu Display Time
		Sets the length of time the OSD will remain active after your last key
	Menu	press. The range is from 5 to 30 seconds in 5-second increments.
	Menu	Menu Position
	Settings	Menu Position
	Settings	Sets the On-Screen Display (OSD) menu position.
		Reminder Message
		Sets the reminder messages on or off.

		Direct Power On
		Allows the projector to turn on automatically once the power is fed
		through the power cord.
		Auto Power Off
		Allows the projector to turn off automatically if no input signal is
		detected after a set period of time. See "Setting Auto Power Off" on page
	Operation	63 for details.
	Settings	Blank Timer
		Sets the image blank time when the Blank feature is activated, once
		elapsed the image will return to the screen. See "Hiding the image" on
		page 35 for details.
		Sleep Timer
		Sets the auto-shutdown timer. The timer can be set to a value between
		30 minutes and 12 hours.

	Remote	Allows you to enable all the remote receivers or one specific remote
	Receiver	receiver on the projector.

58 Operation

Image 58

BenQ MX761 System Setup Basic menu Function Description Quick Auto, Search, Color Space, Conversion, Presentation, Timer

Contents

Welcome MX760/MX761 Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Rear/lower sideZoom ring Power indicator lightFocus ring LeftAuto Remote controlTest Keystone/Arrow buttons / Up DownMIC/VOL + Operating the Laser pointerMute Numeric buttonsReplacing the remote control batteries Remote control effective rangeApprox.+15º Front Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeWhen the projector position is fixed Shifting the projection lensConnection Video cable Hdmi cable ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio BestAbout the microphone input Playing sound through the projectorDevice Page Starting up the projector OperationOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure Write down the number and turn off your projectorDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionFreezing the image Utilizing FAQ functionRemote paging operations Hiding the imageLocking control keys To activate the High Altitude ModeUsing the remote control Operating in a high altitude environmentAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Main menu Sub-menu Options Menu operationMenu system BasicAdvanced Advanced Network Description of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSettings System Setup Basic menu Function Description Quick AutoTimer SearchBackground Settings Security DescriptionPanel Key LockBaud Rate System Setup Advanced menu Function DescriptionReset All Test PatternSystem Features ServiceCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Tighten the screw that secures the lamp Resetting the lamp timer Connect the power and restart the projectorTighten the screw that secures the lamp cover Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsCeiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 128 mm H x 252 mm D Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs HorizontalCopyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement for European users Regulation statementsFCC statement for United States users Weee directive