Focus ring, Zoom ring, Power indicator light, Left | BenQ MX761

	Controls and functions
	Projector		8.	TEMPerature warning light
			8.	TEMPerature warning light
				Lights up red if the projector's
		8		temperature becomes too high.
	1	8	9.	LAMP indicator light
	2	9		Indicates the status of the lamp. Lights up
	3			Indicates the status of the lamp. Lights up
	3			or flashes when the lamp has developed a
				or flashes when the lamp has developed a
	4	10		problem.
		11	10.	AUTO
	5	12		Automatically determines the best picture
	6	13		Automatically determines the best picture
	6	13		timings for the displayed image.
	7	14		timings for the displayed image.
	7	14	11.	Keystone/Arrow keys (	/	Up,	/
		11	11.	Keystone/Arrow keys (	/	Up,	/
		11		Down)
				Down)

1.Focus ring

Adjusts the focus of the projected image.

2.Zoom ring

Adjusts the size of the image.

3.POWER indicator light

Lights up or flashes when the projector is under operation.

4.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

5. POWER

Toggles the projector between standby mode and on.

6. Left/

Starts the FAQ function.

7.BLANK

Used to hide the screen picture.

Manually corrects distorted images resulting from an angled projection.

12. Right/

Activates panel key lock.

When the On-Screen Display (OSD) menu is activated, the #6, #11, and #12 keys are used as directional arrows to select the desired menu items and to make adjustments.

13.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

14.SOURCE

Displays the source selection bar.

10 Introduction

Image 10

BenQ MX761 user manual Focus ring, Zoom ring, Power indicator light, Left, Right

Contents

Welcome MX760/MX761 Digital Projector Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructions Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearance Serviced InstalledIt from the power supplys power outlet Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Projector exterior view Rear/lower side Zoom ring Power indicator lightFocus ring Left Auto Remote controlTest Keystone/Arrow buttons / Up Down MIC/VOL + Operating the Laser pointerMute Numeric buttons Replacing the remote control batteries Remote control effective rangeApprox.+15º Front Table Positioning your projectorChoosing a location Front Ceiling Projection dimensions Obtaining a preferred projected image size When the projector position is fixed Shifting the projection lens Connection Video cable Hdmi cable Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Best About the microphone input Playing sound through the projectorDevice Page Starting up the projector OperationOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTER Changing the password If you forget the passwordEntering the password recall procedure Write down the number and turn off your projector Disabling the password function Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projected Count Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection Description Freezing the image Utilizing FAQ functionRemote paging operations Hiding the image Locking control keys To activate the High Altitude ModeUsing the remote control Operating in a high altitude environment Adjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring Tone If you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environment Wireless connection Highlight Wireless LAN and press MODE/ENTER Controlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Main menu Sub-menu Options Menu operationMenu system Basic Advanced Advanced Network Description of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function Description Teaching Settings System Setup Basic menu Function Description Quick AutoTimer Search Background Settings Security DescriptionPanel Key Lock Baud Rate System Setup Advanced menu Function DescriptionReset All Test Pattern System Features ServiceCurrent Status Maintenance Care of the projector Lamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Tighten the screw that secures the lamp Resetting the lamp timer Connect the power and restart the projectorTighten the screw that secures the lamp cover Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Ceiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 128 mm H x 252 mm D Unit mm Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Horizontal Copyright Warranty and Copyright informationLimited warranty Disclaimer EEC statement for European users Regulation statementsFCC statement for United States users Weee directive